Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
For the flow described in Problem, obtain the differential equation of motion if vθ = f(r; t).
Problem:-
The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are concentric. Fluid enters at A, flows through the annulus between the case and the drum, and leaves at B.
The pressure at B is higher than that at A, the difference being ?ρ: The length of the annulus is L.
The width of the annulus h is very small compared to the diameter of the drum, so that the flow in the annulus is equivalent to the flow between two flat plates. Assume the flow to be laminar.
Find the pressure rise and efficiency as a function of the flow rate per unit depth.
2. Determine the velocity profile in a fluid situated between two coaxial rotating cylinders. Let the inner cylinder have radius R1, and angular velocity Ω1; let the outer cylinder have radius R2 and angular velocity Ω2.
A copper wire has a diameter of 2.05 mm and carries a current of 5 A due solely to electrons. (these values are common in residential wiring.) Each electron is has a charge of of -1.6 × 10-19 C.
The frame object from question 1 uses a BorderLayout by default. Write Java statements to create a JTextfield object and place it into the bottom part of the frame object's window. Describe the sequence of steps needed to create 3 labels and place
a) The excitation voltage (Eaf), line-to-line when the generator is operating at rated voltage and current at apower factor of 0.9 lagging. b) The full load voltage regulation If the load is changed to a pure resistance and the generator is to opera..
Design a full-wave bridge rectifier circuit to deliver 10 volts de with less than 0.1 volt (pp) ripple into a load draWing up to 10mA. Choose the appropriate ac input voltage. assuming 0.6 volt diode drops.
Design RD and the transistor width-to-length ratio such that ID = 12 mA for V1 = 5 V and VDS = 0.15 V and find the labeled node voltages.
A 3-bit " comparator" circuit receives two 3-bit numbers, P = P2P1P0 and Q=Q2Q1Q0. Design a minimal sum-of-products circuit that produces a 1 output if and only if P
A parallel plate capacitive sensor is used to measure displacement. The area of the plates is A and the gap between the plates is d. The space between the plates is completely filled by material with a dielectric constant of er.
A recording trace r(t) is definedas r(t) = s(t) + n(t), where s(t) =10sin(20?t) (i.e., a 10 Hz sine wave, given f= 2f) is the signal and n(t) = sin(120t) (i.e., the 60 Hz electromagnetic noise) the noise.
The average output load voltage
When we opt for cell splitting to increase system capacity, what would be the minimum practical cell size? Define a paging system (i.e., What does it do?).
Suppose that after 24 h the voltage across a 100-F super capacitor is 4:75 V. What is the equivalent leakage resistance in parallel with the capacitor?
A variant of the binary symmetric communication channel described in class is called a binary erasure channel. The transmitter sends a ‘0' or ‘1,' but at the receiver there are three possibilities: a ‘0' or ‘1' or ‘undecided bit..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd