Find the pipe friction head loss between the two points

Assignment Help Civil Engineering
Reference no: EM13319047

Water flows through a pipe at 14cfs. At a point where the pipe diameter is 18in. the pressure is 30 psi; at a second point, further along the flow path and 2 ft lower than the first, the diameter is 9in. and the pressure is 18psi. Find the pipe friction head loss between the two points. Neglect other head losses

Reference no: EM13319047

Questions Cloud

Explain compounds from most acidic to least : Rank PhCH3, Ph2CH2, and Ph3CH in order of acidity Rank the following compounds from most acidic to least
Quantity combinations favored by each of the three partners : Larry, Curly, Moe run the only saloon in town. Larry wants to sell as many drinks as possible. Moe wants to make the largest possible profits. Using a single diagram of the saloon's demand curve and its cost curves, show the price and.
Calculate the fraction of vocs in the exhaust : Assume that gasoline is burned with 99% efficiency in a car engine, with 1% remaining unburned in the exhaust gases as VOCs. If the engine exhausts 16 kg of gases (MW = 30) for each kg of gasoline (MW = 100)
Describe what might be required from a worker : How might Andrew be supported or assisted to access and use support services and associated resources and describe what might be required from a worker when supporting Andrew according to Organisational policies, protocols and procedures?
Find the pipe friction head loss between the two points : Water flows through a pipe at 14cfs. At a point where the pipe diameter is 18in. the pressure is 30 psi; at a second point, further along the flow path and 2 ft lower than the first, the diameter is 9in. and the pressure is 18psi.
The price elasticity of demand for health care has been : The price elasticity of demand for health care has been estimated to be ?0.2. Characterize this demand as price elastic, unit price elastic, or price inelastic.
Calculate how much heat must be added in the scenario : What is the theoretical maximum amount of work that could be done by a gas in a piston expanding from 10 L to 20 L (pressure of the surrounding atmosphere is 100 KPa)
Calculate the values of mpc : Suppose a four sector economy C=200+0,65Yd calculate the values of MPC, MPM, MPT
Acknowledge own strengths and self-care capacity : How could Jack be supported to identify and acknowledge his own strengths and self-care capacity?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What are pressure heads at the interface and at the bottom

A stratified lake could be idealized as two layers: with 7.0 m of fresh water on top and 10.0 m of cold water (specific gravity = 1.02) on the bottom. What are the pressure heads at the interface and at the bottom of the lake, in terms of water col..

  What is the discharge through the pipe for water temperature

A fire hydrant is supplied through a 6 inch cast iron pipe of 16,000 feet length. The total drop in pressure is limited to 35 psi. What is the discharge through the pipe for a water temperature of 80°F ((kinematic viscosity) = 0.93 × 10-5 ft2/sec)

  What is the pressure head

Water in a pip has a pressure of 22.1 lb/ft2. What is the pressure head?

  What is the average degree of consolidation for clay layer

A normally consolidated clay layer is 4 m thick (one way drainage). From the application of a given pressure, the total anticipated primary consolidation settlement will be 80mm. What is the average degree of consolidation for the clay layer.

  Determine what will be carbondioxide level 10 years later

Assume to just using coal as an electric energy source. Take efficency as %50 for average power plant.If the carbondioxide level is 400 ppm by volume now, what will be the carbondioxide level 10 years later

  Compute the change in volume of water stored over one year

Annual rainfall over the watershed is 36 inches and the annual runoff from the catchment is 12 inches. Evaporation from the reservoir averages 40 inches per year. The municipal water demand equals 100 million gallons per day

  Design of wastewater treatment plant for a community

Consider the design of wastewater treatment plant for a community wiyh average daily and peak hourly wastewater design flows of 2.0 mgd. The raw sewage has an average of 230 mg/l BOD5 and 260 mg/l of suspended solids.

  What should be thickness of the confined aquifer for strata

The first stratum is confined, and the second one is unconfined, and the water surface elevations in the channels are 24 m and 16 m above the bottom of the unconfined aquifer.

  Calculate the minimum required minimum wall thickness

A tubular aluminium bar (G=28GPa) of square cross section with outer dimensions 50mm x 50mm must resist a torque T=300Nm. Calculate the minimum required wall thickness t_min if allowbale shear stress is 20MPa

  Determine what is the carts speed at point b

The cart takes 5.00s to go from point A to point C, and the cart takes 1.90s to go from point B to point C. What is the cart's speed at point B. Express answer numerically to three significant figures in feet per second.

  Determine how much power will be required above sea level

If I raise a 1000 lbf weight 100 feet above sea level on earth in 10 seconds how much power will be required

  Determine what would be the flow rate in gpm

Suppose that a water treatment plant has a Parshall Flume with a 4 ft wide throat. a) If the upstream depth of the water (ha) is 1 ft and the depth of the water in the throat section (hb) is 0.65 ft, what is the flow rate in gpm

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd