Find the percent uncertainty due to accuracy and resolution

Reference no: EM13719951

Question 1: An accelerometer has an electrical output voltage and is approximately linear. The sensitivity of this transducer is 10 mV/g. Note: 1 g = 32.2 ft/s². Determine the measured acceleration in units of ft/s² and in units of m/s² when the output is 1.6 volts.

Question 2: A digital voltmeter has an input range of 0 to 30 V and displays three significant figures. The manufacturer claims an accuracy of +2% of full scale. A voltage reading is taken as 12.5 V. Determine the percent uncertainty due to accuracy and the percent uncertainty due to resolution.

Question 3: A strip of unknown metal is "L" in. long and has cross section of "w" in. by "t" in. It is subjected to an axial load of "p" lbf. Two strain gages ate attached to the surface, one in the axial direction and one in the transverse direction. The axial gage indicates a strain of "ε_a" µstrain and the transverse gage indicates a strain of "ε_t" µstrain (compression). Determine the modulus of the elasticity and Poisson's ratio.

P(lbf)	L(in)	w(in)	t(in)	ε_a (µstrain)	ε_t (µstrain)
4200	12	1	0.1200	1150	-335

Question 4: Calibration of a strain gage load cell has produced the following set of data as output voltage from the) ridge circuit for known applied loads. The supply voltage for the bridge circuit during calibration is 12 V. Determine the calibration constant for the load cell in units of (mV/V) / lb. The load cell is used to measure an unknown load. The output from the cell is 0.85 mV. Determine the unknown load.

Load (lb)	0.00	2.00	5.00	10.00	20.00
V_out (mV)	0.00	0.11	0.25	0.49	1.02

Question 5: An internal combustion engine is driving an electric dynamometer. The torque arm length is 0.45m (from the axis) and the measured force is 225 N. A tachometer indicates the shaft speed is 3500 rpm. Determine the engine torque and engine power.

Question 6: A 3500 Hz sine wave with 4.25 V_peak amplitude is to be sampled with a digital oscilloscope. The scope is a 16-bit device and the user can select either a +/- 10V range or a +/- 5 V range. Determine the uncertainty (or bit-error) of the measured amplitude for both ranges.

Question 7: A filter circuit is constructed of a resistor, 1500x10³ ohms, and capacitor, 25 µfarads. Determine the time constant for the circuit and the filter cut-off frequency.

Question 8: A sensor is modeled as a mass-spring system with mass, m = 0.25 lbm, and spring, k = 20 ibf/in, and negligible damping, c = lbf-s/ft. Determine the circular natural frequency, ω_n (rad/s), and the natural frequency, f_n (Hz).

Question 9: Power transmitted through the drive shaft of a car results in a rotational speed of 2400 rpm with a power transmission of 200 horsepower. Determine the torque transmitted through the drive shaft.

Question 10: An analog signal containing frequencies of 300 Hz, 450 Hz, and 700Hz is to be sampled with a DAQ card in a computer. Determine the suggested frequency sampling rate, Hz, needed to capture the frequency components without aliasing.

Question 11: A large sampling (N>5000) from a population of bearings is taken to measure the bearing diameter. An automated measuring system indicates diameter mean of 0.5 inches and variance of 0.0001 inches². Determine the lower and upper range values containing 99.73% of the population.

Question 12: A first order measuring system is subjected to a step input during calibration. The step input at time = 0 seconds is 10 units and at 1.5 seconds the system output is 8 units. Determine the time constant for the measuring system. Determine the time at which the system output reaches a value of 10 units.

Reference no: EM13719951

Questions Cloud

What is air monitoring and how to perform it : Identify the reasons for performing air monitoring. What reporting is necessary. What factors should you take into account when conducting air monitoring in an outside area

Calculate the binding energy in joules of a cobalt atom : Determine the binding energy in joules of a cobalt atom with 27 protons, 32 neutrons and a mass of 97.958205 x 10-27 kg

Assignment-cloud computing : Many organizations have now adopted or begun to offer cloud computing. This type of computing has advantages and disadvantages that may vary from organization to organization.

Assignment risk assessment plan : We all face potential hazards in our workplaces and in our homes. Ideally we can eliminate or control many of these; however, if and when they occur, a Risk Assessment Plan is our best defense. Explain the task being performed when the risk might o..

Find the percent uncertainty due to accuracy and resolution : A digital voltmeter has an input range of 0 to 30 V and displays three significant figures. The manufacturer claims an accuracy of +2% of full scale. A voltage reading is taken as 12.5 V. Determine the percent uncertainty due to accuracy and the p..

What is the isentropic efficiency : H2O at 350oF, 60 psi enters an insulated nozzle at 10 ft/s. It leaves at 1440 ft/s and 35 psi. What is the isentropic efficiency?

Develop a set of hrm practices : Analyze the organization and develop a set of HRM practices based upon textbook illustrations and figures. You will develop an 8-10 page research paper (not including the title and reference pages) modeling one or more of the illustrations from t..

Determine acceleration of the ram as well as reaction forces : The figure shows a weapon called a battering ram (modern large battering rams are typically mounted on armored vehicles). The ram has weight Wr=2590 lb, center of mass at E, and radius of gyration kE=6.4 ft. Also let the distance between points A a..

Find the largest torque that can be applied : The composite shaft consists of three sections: 1) a solid brass core, 2) a middle steel tube, and 3) an outer aluminium tube. The brass core (Gb= 39 GPa) has a diameter of 50 mm. The steel tube (Gs= 77 GPa) has an inner diameter of 50 mm and an ou..

User Account

All Pages