Find the net power output of this plant and the required

Assignment Help Mechanical Engineering
Reference no: EM13644577

A small Rankine power plant produces 25 kg/s of steam at 3 MPa and 600°C in the boiler. It uses water from a river to cool the condenser. The water comes into the condenser at 12°C and leaves at 15°C. The condensed steam leaves the condenser saturated at 45°C. Find the net power output of this plant and the required mass flow rate of river water. The turbine and pump operate isentropically.

Reference no: EM13644577

Questions Cloud

Suppose that x is a geometric random variable a prove that : suppose that x is a geometric random variable. a prove that for positive integers n and k pxnkxgtnpxk. bexplain what
A door-to-door residential solar electrical system salesman : a door-to-door residential solar electrical system salesman is required to document four in-home visits each day.
Time taken by a randomly selected applicant for a mortgage : 1. rockwell hardness of pins of a certain type is known to have a mean value of 50 and a standard deviation of 1.2.
The cost per item at a supermarket follows an exponential : the cost per item at a supermarket follows an exponential distribution. there are many inexpensive items and a few
Find the net power output of this plant and the required : a small rankine power plant produces 25 kgs of steam at 3 mpa and 600degc in the boiler. it uses water from a river to
A recent study of cardiovascular risk factors reported that : 1. diastolic blood pressure are approximately normally distributed with a mean of 75 and a standard deviation of 10 a.
The boiler pressure is 30 mpa and the cycle has a high : a utility plant runs an ideal rankine cycle with water. the boiler pressure is 3.0 mpa and the cycle has a high
If stocks 1 and 2 have expected returns of 009 and 010 per : in order to fund her retirement michele requires a portfolio with an expected return of 0.10 per year over the next 30
An aqueous ester hydrolysis reaction a -gt b c has k 002 : an aqueous ester hydrolysis reaction a -gt b c has k 0.02 min-1 and an equilibrium constant of 10 with all

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A curved rectangular bar has a mean radius of 6 in and

a curved rectangular bar has a mean radius of 6 in and cross section width b2.5 in and depth h 1.5 in. 1. determine the

  Knowing that e045x106 psi determine a the reactions at a

a polystyrene rod consisting of two cyldindrical portions ab and bc is restrained at both ends and supports two 6-kip

  Determine the volume of the tank in m3 and the final

five kilograms of water are contained in a closed rigid tank at an initial pressure of 20 bar and a quality of 50. heat

  Where are hogr used in general

What is hogr? How much steam pressure is required to maintain adequate vacuum with it? Where are hogr used in general?

  If a mass of cobalt is replaced by a compound with a

if a mass of cobalt is replaced by a compound with a density of 4.13 mgm3 and results in a mass reduction of 0.79 kg

  Consider a steam power plant that operates between the

consider a steam power plant that operates between the pressure limits of 10 mpa and 20 kpa. steam enters the pump as

  The appropriate pumps are used for the water leaving the

consider a regenerative cycle utilizing steam as the working fluid. steam enters the turbine at 3.5 mpa 400oc and

  The pressure of the air in the cylinder is 140kpa model

air in contained in a vertical cylinder fitted with a frictionless piston and two sets of stops. the volume is .05m3

  Air at 358c 1 atm and 50 relative humidity enters a

air at 358c 1 atm and 50 relative humidity enters a dehumidifier operating at steady state. saturated moist air and

  A steam power plant operates on an ideal regenerative

a steam power plant operates on an ideal regenerative rankine cycle with two open feedwater heaters. steam enters the

  The weight of all other links is negligible at the instant

the compressor mechanism shown in figure is driven clockwise by a dc electric motor at a constant rate of 800 rpm. in

  How will you develop a component machining process plan for

a manufacturing firm needs to manufacture cylindrical components on a cnc lathe. the differential between the incoming

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd