Find the net power input to the motor

Assignment Help Mechanical Engineering
Reference no: EM131392454

An electric motor draws a current of 10 amperes (A) with a voltage of 110 V. The output shaft develops a torque of 9.5 N#m and a rotational speed of 1000 rpm. All operating data are constant with time. Determine

(a) the electric power required by the motor and the power developed by the output shaft, each in kilowatts;

(b) the net power input to the motor, in kilowatts;

(c) the amount of energy transferred to the motor by electrical work and the amount of energy transferred out of the motor by the shaft in kW# h and Btu, during 2 h of operation.

2184_da109c54-b68d-47e0-8c91-6db8eaaac58b.png

Reference no: EM131392454

Questions Cloud

Design a signal conditioning system : Design a signal conditioning system that provides an output of 0.0 to 5.0 V as R3 varies from 120 to 14Ω. Plot versus . Evaluate the linearity.
Potential income on leisure and three fifth on consumption : Mrs. Smith has a guaranteed income of $20 per day from an inheritance. Her preferences require her always to spend two fifth (40%) of her potential income on leisure (H) and three fifth (60%) on consumption (C). What is Mrs. Smith budget constraint i..
Determine the torque of each shaft : The input shaft to a gearbox rotates at 2000 rpm and transmits a power of 40 kW. The output shaft power is 36 kW at a rotational speed of 500 rpm. Determine the torque of each shaft, in N#m.
How the power varies with lsb changes : Using a 10-V DAC followed by an amplifier with a high-current output, calculate the settings from minimum to maximum heat dissipation, and how the power varies with LSB changes.
Find the net power input to the motor : An electric motor draws a current of 10 amperes (A) with a voltage of 110 V. The output shaft develops a torque of 9.5 N#m and a rotational speed of 1000 rpm. All operating data are constant with time.
Does the voltage vary linearly with resistance : Prepare graphs of the divider voltage versus transducer resistance for given Problem. Does the voltage vary linearly with resistance?
Transportation costs are immaterial : In a world where transportation costs are immaterial (close to zero), where trade barriers are very low or do not exist, and where differences between nations as regards to labor and other conditions are real, firms must expand internationally if the..
Assume that the uncovered interest parity condition : Suppose the country of Utopia is an open economy and its only trading partner is the United States. In addition, we assume that the uncovered interest parity (UIP) condition holds between both countries. The government of Utopia is currently running ..
Situation using budget constraint and indifference curve : Suppose that good X is on the horizontal axis and good Y is on the vertical axis. Good X costs twice as much as good Y. Ann chooses a bundle that takes up all of her budget. The MRS of X for Y at this bundle is equal to 2. Please illustrate this situ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At the exit the pressure is 24 bar and the temperature is

air flows through a well-insulated nozzle operating at steady state. at the inlet the pressure is 5 bar the temperature

  Air at 50 psia and 90 f flows at the rate of 16 lbms

air at 50 psia and 90 f flows at the rate of 1.6 lbms through an insulated turbine. if the air delivers 11.5 hp to the

  Determine the amount of steam produced per hour

Determine the amount of steam produced per hour, if the total heat loss is 10% of the heat available for steam raising - What would be the new heat transfer area if the fluids were in parallel flow

  It has been determined that a point in a load-carrying

it has been determined that a point in a load-carrying member is subjected to the following stress condition sx 400 mpa

  Determine the maximum value p for which the body is stable

The cylinder of mass m and radius r rolls without slipping on the circular surface of radius p. Attached to the cylinder is a small body of mass m/4. Determine the maximum value of p for which the body is stable in the equilibrium position shown.

  Evaluate the basic cycle efficiency

introducing reheat to the turbine by splitting the turbine pressure ratio such that the pressure ratio of each stage is the square root of the compressor pressure ratio.

  What are the three phases in shop floor control

How does aggregate planning differ from the master production scheduling?

  Estimate the increase in pressure from the inside

Estimate the increase in pressure from the inside of the pipe to the outside of the pipe midway through the elbow if the radius of curvature of the elbow averages 4 cm at the midway section.

  Electricity supplied to the water heater

Perform a full exergy accounting, in kJ, of the electricity supplied to the water heater. Model the water as incompressible with a specific heat c 5 4.18 kJ/kg ? K. Let T0 5 23°C.

  Determine rate of insulin production from gel in moles

Genetically engineered bacteria (used to produce insulin) are immobilized in a solid agar disc (cylinder with flat surface facing up - 100 cm diameter, 5 cm height), which is exposed to large volume of stirred liquid media on both of the flat surface..

  Find the crank position corresponding to the maximum piston

a find the crank position corresponding to the maximum piston velocity for an in-line slider crank mechanism. crank

  Assume that the condenser exit is liquid whose temperature

a kansas farmer heats his house with a heat pump using r134a generating a temperature of 50 deg c at the exit of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd