Find the natural frequency of oscillation

Assignment Help Mechanical Engineering
Reference no: EM131508398

Question: A cylindrical buoy of cross-sectional area A and total mass m is first depressed from equilibrium and then allowed to oscillate (Fig.). Denote the mass density of the liquid by ϒ and determine the natural frequency of oscillation.

295_2.16.png

Reference no: EM131508398

Questions Cloud

Describe the forces that cause the tectonic plates to move : Describe forces that cause the tectonic plates to move. Describe different kinds of plate tectonic boundaries and what happens at each type of plate boundary
What did you learn from the problem solving collaboration : What did you learn from the Problem Solving Collaboration assignment? How this assignment involved research, team work, critical thinking and presentation.
Determine the stability nature of each equilibrium position : A uniform rigid bar of total mass in and length is hinged at point ? to a shaft rotating with the constant angular velocity S2 about a vertical axis.
Write a process that the ccb activity will follow : Your assignment is to write a process that the configuration control board activity will follow during the maintenance period.
Find the natural frequency of oscillation : A cylindrical buoy of cross-sectional area A and total mass m is first depressed from equilibrium and then allowed to oscillate (Fig.).
What evidence did alfred wegener use to support hypothesis : What evidence did Alfred Wegener use to support his hypothesis of continental drift? What additional evidence was added later
Success of an organization : You have learned this term that stakeholders play an important role in the success of an organization.
Determine the natural frequency of the system : Determine the natural frequency of the system of Fig. for k1 = k2 = 0.8 x 105 N/m, k3 = 2.4 x 105 N/m and m = 240 kg.
Discuss the deliverables of the data warehouse design phase : Fact Table Deliverables- Discuss the deliverables of the data warehouse design phase. What is the importance of the data mapping document?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the amount of recycle gas in mol per 100 kg of p if

to save energy stack gas from a furnace is used to dry rice. a gas containing 4.73 mol water is fed into the dryer as

  A log with a specific gravity of 067 is floating in water

a log with a specific gravity of 0.67 is floating in water. determine the percentage of the volume of the log that is

  What is the ratio of your weight at the top of the ride to

while at the county fair you decide to ride the ferris wheel. having eaten too many candy apples and elephant ears you

  If the winch exerts a force of t125s on the cable where 13m

the 2 mg car is being towed by a winch. if the winch exerts a force of t125s on the cable where 13m is the displacement

  What should your microcomputer do when the fifo is full why

What should your microcomputer do when the FIFO is full? Why?

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  Will the launch come to rest before hitting the wharf

A launch approaches a wharf at a speed of 10.5 knots(=5.4m/s).The engine are put in the reverse when the launch is 10 m from the wharf, the retardation being 1.25m/s squared. will the launch come to rest before hitting the wharf.. If not, with wha..

  Derive an expression for the deflection between the points

Omit terms that are likely to be negligible but enumerate any such terms. (You may want to use symmetry.)

  Find the mass of the flywheel required

The maximum and minimum speeds are not to vary more than 1 percent on either side of the mean speed. Find the mass of the flywheel required, if the radius of gyration is 0.6m.

  Calculate the molar absorptivity of kmno4, at 520 nm

Calculate the molar absorptivity of KMnO4, at 520 nm.

  Determine the radial wall thickness-speed in rpm

A flat disk of outer radius b-125mm and inner radius a=25mm is shrink-fitted onto a shaft of radius 25.05mm. Both members are made of steel with E=200Gpa, v=0.3, and p=7.8 KN.s2/m4. Determine (a) the speed in rpm at which the interface pressure becom..

  Determine the distance between the laser and photodetector

A laser triangulation system has the laser mounted at a 35° angle from the vertical.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd