Find the molar absorptivity of the complex

Assignment Help Mechanical Engineering
Reference no: EM131121777

The accompanying data were obtained in a slope-ratio investigation of the complex formed between Ni2+and 1-eyclopentene-1-dithiocarboxylie acid (CDA). The measurements were made at 530 nm in 1.00-cm cells.

1857_87661e74-6a91-4833-9eab-9dc523f7b69c.png

(a) Determine the formula of the complex. Use linear least-squares to analyze the data.

(b) Find the molar absorptivity of the complex and its uncertainty.

Reference no: EM131121777

Questions Cloud

Estimate the daily heat loss through the wall : Assuming quasi steady conditions for which changes in energy storage within the wall may be neglected, estimate the daily heat loss through the wall if its total surface area is 200 m2.
What do you think about tads expansion plans : How would you describe Sunset Boards' cash flows for 2014? Write a brief discussion. In light of your discussion in the previous question, what do you think about Tad's expansion plans?
A symmetric traveling salesman problem : Traveling Salesman Problem/Triangle Inequality) Consider a symmetric traveling salesman problem where the arc costs are nonnegative and satisfy the following triangle inequality:
Describe the different types of wireless signals : Analyze the maturity of each type of wireless signal and give your opinion on whether or not you believe that type of wireless signal is stable. Is there potential for change and further advancement, or do you suspect there will be limited change?..
Find the molar absorptivity of the complex : Determine the formula of the complex. Use linear least-squares to analyze the data.
Most significant differences in delivering a presentation : What are the most significant differences in delivering a presentation in person versus online? What are the most significant differences in watching a presentation in person versus online? How does the desired effect on the audience influence your c..
Explore the effect of the insulation thickness : Explore the effect of the insulation thickness on the temperature of the aluminum and the heat loss per unit tube length
Management repository can be used throughout organization : Why do all the business units in an organization that use technology need to be involved in developing management information systems? How does that relate to the goal that a “knowledge-management repository” can be used throughout the organization?
Calculate the timing of password-guessing attacks : Argue for a particular amount of time as the starting point for "secure." That is, suppose an attacker plans to use a brute-force attack to determine a password. For what value of x (the total amount of time to try as many passwords as necessary) ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd