Find the minimum sinr needed for reliable communication

Assignment Help Electrical Engineering
Reference no: EM13967949

This exercise applies basic capacity results to analyze the IS-856 system. You should use the parameters of IS-865 given in the text.

1. The table in the IS-865 example in the text gives the SINR thresholds for using the various rates. What would the thresholds have been if capacity-achieving codes were used? Are the codes used in IS-856 close to optimal? (You can assume that the interference plus noise is Gaussian and that the channel is time-invariant over the time-scale of the coding.)

2. At low rates, the coding is performed by a turbo code followed by a repetition code to reduce the complexity. How much is the sub- optimality of the IS-865 codes due to the repetition structure? In particular, at the lowest rate of 38.4 kbits/s, coded symbols are repeated 16 times. With only this constraint on the code, find the minimum SINR needed for reliable communication. Comparing this to the corresponding threshold calculated in part (1), can you conclude whether one loses a lot from the repetition?

Reference no: EM13967949

Questions Cloud

What kind of opinions should you attempt to capture : To what extent are exit interviews meaningful and what kind of opinions should you attempt to capture? How are these opinions relevant to employee separation and retention
What are typical values of tc at different vehicular speeds : Consider the following pilot (or training symbol) based scheme that converts the non-coherent communication into a coherent one by providing receiver CSI. The first symbol of the block is a known symbol and information is sent in the remaining sym..
Examine major benefits that report provide for organization : Examine the major benefits that this report can provide for the organization, and suggest two uses for the information contained therein. Justify your response.
Describe the speaker''s movement and gestures. : How does the speaker's nonverbal communication enhance or detract from their verbal delivery? (Describe at least three examples of how the speaker's nonverbals match or)
Find the minimum sinr needed for reliable communication : The table in the IS-865 example in the text gives the SINR thresholds for using the various rates. What would the thresholds have been if capacity-achieving codes were used? Are the codes used in IS-856 close to optimal?
Compute numerically and plot the average power as a function : Compute numerically and plot the average power as a function of the target rate for different L to get a sense of the amount of gain from having multiple receive antennas. Qualitatively describe the nature of the performance gain.
Present discounted value of receiving : If the interest rate is 10%, what is the present discounted value of receiving $100 next year?
Theories of justice often comprise three categories : Write a conclusion identifying your preferred theory of justice along with your rationale for choosing the theory.
Compute the capacity of the fast fading channel : Consider the frequency-selective channel with CSI only at the receiver with L i.i.d. Rayleigh faded paths. Compute the capacity of the fast fading channel. Give approximate expressions at the high and low SNR regimes.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much work is needed to move one charge to the position

Three equal point charges Q form an equilateral triangle of side length a. How much work is needed to move one charge to the position halfway between the other two

  Calculate the mmf when the machine operates

calculate the mmf when the machine operates at rated voltage at full load? PLease explain how to get the solution to this problem?

  Determine the width of the depletion region

A pn junction with Nd=4x10^16 cm^-3 and Na=3 x 10^15 cm^3 experiences a reverse bias voltage of 1.6V (a) Determine the width of the depletion region and the junction capacitance per unit area

  Explain what is the advantage of a synchronous counter

Flip-flops must be in what mode (Set, Reset, Hold, or Toggle) in order to divide a clock's frequency when building a counter What is the advantage of a synchronous counter as compared to a ripple counter

  Calculate resistance before moving on to the series sections

A series-parallel circuit contains both series and parallel connections in different arrangements. Do you find it useful to isolate the parallel sections and calculate their resistance first

  When circut is reflected to primary side of the transformer

An ideal transformer has five times more turns on the primary than the secondary. A0.1-H inductor and a 0.1uf capacitor are connedted in parallel across the secondary of the transformer.

  Determine what is the max height obtained

A ball is shot into the air at 30 degress above the horizontal. It's initial Velocity is 5m/s and lands at the same height that it is launched from. How far does it travel horizontally

  Calculate the impulse response using laplace transforms

using 1/(s+2)(s+4) + c find when the poles are repeated and use that value to calculate the impulse response using laplace transforms. Calculate the step response when c = 10 using Laplace transforms.

  Determine the appropriate operating frequency and voltage

A three-phase induction motor has been tested, and has small stator resistance. At 230 V, 60 Hz, the motor produces 40 N-m at 1740 RPM.a) Given a 40 N-m load, input of 115 V and 30 Hz, what operating speed do you expect

  Find the kw-ruling and the overall efficiency of rate

An electric kettle needs six minutes to boil 2 kg of water from the initial temperature of 20"C. The cost of electrical energy required for operation is 12 paise, the rate being 40 paise per kWh.

  Determine and draw expected current and voltage waveforms

Analyze and design a boost converter - analytically determine and draw the expected current and voltage waveforms for each component in your circuit at both light and heavy load.

  Determine the load voltage if the source voltage

Given a simple series circuit similar to that shown in the given image, determine the load voltage if the source voltage is VS= 1200°V, the load current is IL= 10-30°A, and the cable impedance is ZC= 0.5

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd