Find the maximum deflection of a wooden bearer

Assignment Help Civil Engineering
Reference no: EM13320858

Find the maximum deflection of a wooden bearer which has three supports; one at each edge (2) and one in the middle (2m from each other). Bearer holds a UDL over its whole length (4m) of 600 N/m.

Data:
bearer: 0.045x0.12x4 (rectangular)
E=14000 MPa

Reference no: EM13320858

Questions Cloud

Find the flux through the loop : A constant 0.28 T magnetic field passes through a loop at an angle of 35 degrees with respect to the normal of the area of the loop. find the flux through the loop
Find the strength of the magnetic field within the solenoid : In a long solenoid, the density of the wire is 180 turns/cm. find the strength of the magnetic field within the solenoid
What must be the density of the gas at that section : Gas flows at a steady rate in a 120-mm-diameter pipe that enlarges to a 180-mm-diameter pipe. At a certain section of the 120-mm pipe the density of the gas is 165 kg/m^3 and the velocity is 15 m/s.
What is the force per unit length between the wires : Two long, parallel wires carry currents of 0.245 A in the same direction. If the wires are 0.034 m apart, what is the force per unit length between the wires
Find the maximum deflection of a wooden bearer : Find the maximum deflection of a wooden bearer which has three supports; one at each edge (2) and one in the middle (2m from each other). Bearer holds a UDL over its whole length (4m) of 600 N/m.
What is the force on the segment of the wire : A 0.25 m segment of wire lies along the x-axis and carries a current of 4.7 A in the negative x direction. What is the force (magnitude and direction) on the segment of wire
An organizational design plan : An organizational design plan
Find the force on the charge : If the charge is 23 mu/C, the velocity is 1500 m/s, find the force (magnitude and direction) on the charge.
Risk-taking is an important aspect of the leadership : Embracing change requires risk-taking, which needs to be as calculated as possible and based on knowledge rather than mere guesses.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the maximum horsepower that the system can produce

A ssume that one half of the energy incident on the collector goes to this reservoir, which, in turn, serves as a source for a heat engine. If the temperature of the atmosphere is 70 F,

  Proprietorships and last year gross profit

Jack Flubber, who owns sons of Flubber Construction Co. and runs it as a proprietorships had gross profit last year of $ 80000. His personal and family expenses are $ 52000 and he has $ 7000 in exemptions and deductions.

  Find the length of the studs in a rake wall with base height

Find the length of the studs in a rake wall with a 5:12 pitch, a half span of 9'4", 16" OC and a base height of 7'3".

  Estimate cross sectional dimension of bar under strain

A 1000 in diameter solid steel (p= 0.303) bar is 10.0 ft long. Under a tensile load. (a) Estimate the lateral strain experienced by the bar (b) Estimate the cross sectional dimension of the bar when under strain

  Describe at least four basic features of cpm software

Describe the problem of lack of coordination between design and construction in a traditional contract. In agency CM,what expertise does the CM provide during the pre-design and design phase.

  Find magnitude of the total acceleration of roller coaster

the roller coaster track consists of a circle in a vertical plane of radius 150m. find the magnitude of the total acceleration of the roller coaster if, at the time shown, the car is moving at 50 km/hr and is gaining speed at the rate of 0.4g

  Solve for dv by dx and v using differential equations

Consider a simply supported beam with a uniformly distributed load q AND a concentrated load P at midspan. Solve for dv/dx and v using differential equations.

  Effective vertical stresses of the clay layer

The saturated unit weight of the clay is 20kN/m 3 and that of the sand 19 kN/m 3 ; above the water table the unit weight of the sand is 16.5 kN/m 3 . Calculate the effective vertical stresses at the top and bottom of the clay layer.

  Determine the void content

If the dry-rodded unit weight of an aggregate is 105 lb/ft3 (1680 kg/m3) and its specific gravity is 2.65, determine the void content.

  Find the total well losses in and around the pumping well

After the cone of depression has achieved equilibrium, the piezometric heads at two observation wells 40 and 95 m from the pumping well are measured as 78.9 and 83.4 above sea level, respectively.

  What is the total volume of the vocs emitted each day

Assume that there were 1,100,000 vehicles making a 28.5-mi round trip per day, the average vehicle emission rate for VOCs is 1.3 g/VM , and the molecular weight of the VOC emissions from the mobile sources can still be represented by that of metha..

  Determine how would distance be accomplished specifically

A sailboat capsizes a large distance from shore. What might be done to 1) right the boat and 2) prevent this from occurring again. How would this be accomplished specifically

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd