Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Use Smith Chart
1. For a complex load of 30 - 50 j ohm. find the matching circuit consist of ideal capacitor and/or inductor to match the load to 50 ohm impedance at 2GHz. The solution should include circuit schematic and values of each component.
2. For a complex load of 100 + 25 j ohm. find the matching circuit consist of ideal capacitor and/or inductor to match the load to 50 ohm impedance at 500MHz. The solution should include circuit schematic and values of each component
The solar constant at Earth orbit (1 AU = 1 Astronomical Unit - Sun-Earth distance) is ~1400 Watts/m2. Assuming that this Poynting flux magnitude can be associated with a single E- and Hfield (i.e., E × H ),
A 50 ohmlossless air transmission line is terminated in a load impedance ZL = 12.5 + j20 ohm. Find the following using a Smith Chart: the load admittance YL. the closest distance to the load plane where the normalized admittance on the line is 1 + j..
Operation of NPN Bipolar Transistor : a. Describe the operation of a typical NPN bipolar junction transistor used both as an amplifier and a switch. b. List the 4 regions of operation and draw I-V characteristic curve.
An LED with a rated range of VF = 1.4 V to 1.8 V at IF = 20 mA is connected to a driver circuit with a peak output of 14V. What value of current-limiting resistor would be needed to limit the LED current to a maximum value of 20 mA
A linear CW product detector local oscillator has a 500 Hz error while detecting an AM signal. What will the receiver's output sound like What if the receiver is listening to a DSB or SSB signal
A glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving.
(a) a circuit in which one fuse will be damaged and other three not, after making all connections as per you schematic and connecting power supply (b) a circuit in which two fuses will be damaged and other two not,d connecting power supply
For the Circuit shown below, V1=5V, R1= 20 kiloOhm, R2= 100kiloOhm, and C= 0.1 microF. Assume the switch in the circuit below has been open for a long time. At t=0, the switch is closed and at t=5 sec the switch is re-opened.
a) Design a band-pass filter consisting of an RC high-pass filter with a cutoff frequency of 300 Hz and an RC low-pass filter with a cutoff frequency of 3400 Hz. Carefully select R and C of each filter so that one filter does not load the other
A three phase, 25-hp, 440-V, 60-Hz, 1750 rpm, wound-rotor induction motor has the following equivalent circuit parameters:R1=0.20 ohms, X1=1.0 ohms, R2=0.15 ohms, X2=0.8 ohms, Xm=30 ohms The motor is connected to a three phase, 440-V, 60-Hz supply.
Implement a high-speed multiplier which will multiply two 2-bit binary numbers (B1B0 and C1C0) using a 16X4 PROM (lookup table implementation). List the content of all the memory locations in the PROM and describe the operation.
Maximum Amount of Channels A Link Can Carry, A microwave radio link operates over a bandwidth of 400 MHz at C band. The link carries a number of channels of data using FDMA.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd