Find the mass flow rate of the air through the handler m

Assignment Help Mechanical Engineering
Reference no: EM13629181

Consider an IDEAL vapor-compression air conditioner with a cooling capacity of Q dot_c= 4 tons whose evaporator is used to cool dry air in an air handler duct from T_a,in= 75 degrees F down to T_a,out= 62 degrees F. The refrigeration cycle uses R-134a. The evaporator operates at a pressure of 60 psia, and refrigerant exits the evaporator as saturated vapor. The condenser operates at a pressure of 200 psia, and refrigerant exits the condenser as saturated liquid. 1 Ton= 12000 Btu/hr

Find:

a) compressor work per unit mass, w_c, in Btu/lbm

b) the heat transfer from the evaporator per unit mass, q_c, in Btu/lbm

c) cycle COP

d) refrigerant mass flow rate, m dot_r, in lbm/hr

e) the mass flow rate of the air through the handler, m dot_a, in lbm/hr

f) the electric power consumed by the compressor assuming a 100% efficient electric compressor motor

a) w_c= 10.7 Btu/lbm

b)q_c= 55.8 Btu/lbm

c) COP= 5.21

d) m dot_r= 884 lbm/hr

e) m dot_a= 15400 lbm/hr

f) motor power= 2.78 kW

Reference no: EM13629181

Questions Cloud

The fuel is consumed at a constant rate q dmdt and is : a rocket of initial mass m0 including shell and fuel is red vertically at time t 0. the fuel is consumed at a constant
The guidance system of a ship has four modules that must : the guidance system of a ship has four modules that must maintain all function properly for the system to work. two of
Performing an experiment similar to millikans oil drop : performing an experiment similar to millikans oil drop experiment a student measures these charge magnitudes.3.26
Explain the differences between the plane stress fracture : explain the differences between the plane stress fracture toughness and the plane strain fracture toughness. for a
Find the mass flow rate of the air through the handler m : consider an ideal vapor-compression air conditioner with a cooling capacity of q dotc 4 tons whose evaporator is used
The readylite company produces a flashlight in which : the readylite company produces a flashlight in which product managers are trying to decide how long a warranty to
A fighter jet lands on the deck of an aircraft carrier it : a fighter jet lands on the deck of an aircraft carrier. it touches down with a speed of 73.5 ms and comes to a complete
If a company knows that its new employees have an : if a company knows that its new employees have an eighty-five percent learning rate and the first time they perform the
The number of plumbing repaie jobs performed by angurs : the number of plumbing repaie jobs performed by angurs plumbing service in each of the last four years is listed

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A frictionless piston cylinder device with a set of stops

a frictionless piston cylinder device with a set of stops contains .5m3 of saturated h2o vapor at 200 kpa. at this

  Large stationary brayton cycly gas turbine power

Large stationary brayton cycly gas turbine power plant delivers a powr output of 100MW to an electric generator . Minimum temperature is 300K so T1= 300k max temp is 1600k

  If the velocity v of a paticle moving along a straight

if the velocity v of a paticle moving along a straight line decreases linearly with its displacement from 20ms to a

  A four cylinder four stroke gasoline internal combustion

a four cylinder four stroke gasoline internal combustion engine has a bore of 9.4 cm and a stroke of 8.6 cm. the

  The steel of the bend material weighs 51 kg neglecting

when a plastics plant is redesigned a tank exit is now facing the wrong direction and must be connected to a pipe of

  A gate having the cross section shown in fig below closes

a gate having the cross section shown in fig. below closes an opening 5 ft wide and 9 ft high in a water reservoir. the

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  After a period of time the pressure in the tank rises to 15

1 initially an insulated rigid tank contains 3.86 kg of water at 265oc and 1 mpa. a heater in the wall of the tank

  Resolve a vector a which has a magnitude of 50 units and a

resolve a vector a which has a magnitude of 50 units and a direction of 210 degrees into two vetors b and c. c is to be

  The cables direction is 100i - 100j - 100k and it has a

an old wooden telephone pole with a single cross member was blown off center during a recent storm. to temporarily

  Why use the penalty method for implementing boundary

why use the penalty method for implementing boundary conditions? what are the advantagesdisadvantages of direct versus

  The gate opens when water levels reaches h2m on the left

water gate is hinged at point o. angle between the gate and the ground is given alpha 60 degrees. the gate opens when

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd