Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A linear-phase FIR filter should be designed with the ideal magnitude response shown in Figure 1 which represents an narrow band-pass filter. The lower cutoff frequency, fL , is 2,000 Hz, and higher cutoff frequency, fH , is 3,600 Hz. Sampling frequency fS = 8,000 Hz.
I. Using the Fourier method, design a 15-tap filter to obtain noncausal impulse response h[n] for the desired response.
II. Compute a 15-sample Hamming window (noncausal) w[n] then apply the window to the filter.
III. Find the magnitude and the phase response of the filter as a function of normalized frequency, ohm.
The required exposure energy for a positive photoresist is 140 mJ/cm2 and for a negative photoresist is 9 mJ/cm2. Assuming negligible times for loading and unloading wafers, compare the wafer throughput for positive photoresist and negative photor..
What happens to the propagation delay of the N-bit full adder as N is increases from 2 bits to 32 bits Compare and contrast this method of building an adder with the carry look ahead method described in your textbook
Two slits produce fringes on a screen that is at a distance of 2.05 m from the slits. When the wavelength is 608 nm, the fringTwo slits produce fringes on a screen that is at a distance of 2.05 m from the slits. When the wavelength is 608 nm, the f..
Transmit this data wirelessly to a base station for storage. How much bandwidth would you need.
during winter you use an electric heater rated 1000W . heat transfer occurs through four walls each width of 5m and hight 3m layers of walls are concrete , paint, gypsum. temperature outside is 5 degrees celsius what is the temperature inside the ..
Assume the average energy density of sunlight to be 800 w/m^2 ---and the overall photovolatic system efficiency to be 10 percent. Calculate the land area covered with photovolatic cells needed to produce 1000 Mw , the size of a typical large centr..
The tray heats up according to ut = c2?u + h(x, y) where h(x, y) = 5(1 - sin(8πy)) and c2 = 10-4. Assume that u = 200 along each edge. Find the steady state temperature distribution of the tray.
A 78oham lossless planar line was designed but did not meet a requirement. What fraction of the widths of the strip should be added or removed to get the characteristic impedance of 75oham
how to determine the sensitivity of junction depth to changes in furnace temperature by calculating (dxj/xj)/(dT/T) for a drive diffusion.
Assuming dopant atoms are uniformly distributed in a silicon crystal, how far apart are these atoms when the doping concentration is a) 10l5 cm-3, b) 1018 cm-3, c) 5times1020 cm-3. Estimate the resistivity of pure silicon in Ohm-cm
Consider a discrete-time linear time-invariant system with impulse response h[n]. If the input x[n] is a periodic sequence with period N (i.e., if x[n]=x[n+N]), show that the output y[n] is also periodic sequence with period N.
1- Draw a circuit whose output goes to + V sat . When the input signal is below -4V. the output should be -V sat, when the input is above - 4V 2- Design a - 90 phase shift circuit at 1590 Hz , Then for your design calculate 0 at 15 Hz, & 15 KHz
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd