Find the locus of the closed-loop roots with respect to k

Assignment Help Electrical Engineering
Reference no: EM13251531

For the closed-loop system with plant model and controller given by

G(s) = (s2+81)/(s2(s2 + 100)) D(s) = (K (S+1))/(S+13)

(a) Find the locus of the closed-loop roots (poles) with respect to K;

(b) Is there a value of K that will cause all roots to have a damping ratio greater than 0.5?

(c) Find the values of K that yield closed-loop poles with the damping ratio ? = 0.707.
(d) Use Matlab to plot the response of the resulting design to a reference step input.

Reference no: EM13251531

Questions Cloud

State the standard reduction potentials : Refer to the Galvanic cel below (the contents of each half-cell are written beneath each compartment): 0.10 M MnO4- 0.40 M Cr3+
What is the break-even quantity in this case : What is the break-even quantity in this make-or-buy decision? Please include the formula, at least one step of calculation, and the correct answer for full credit.
Explain current is allowed to flow which species is oxidized : When current is allowed to flow, which species is oxidized. What is the value of E0cell
Compute the takt time for a service system : Compute the takt time for a service system that intended to perform a standardized service. The system will have a total work time of 440 minutes per day, two 10-minute breaks, and an hour for lunch. The service system must process 90 jobs a day.
Find the locus of the closed-loop roots with respect to k : For the closed-loop system with plant model and controller given by G(s) = (s2+81)/(s2(s2 + 100)) D(s) = (K (S+1))/(S+13) (a) Find the locus of the closed-loop roots (poles) with respect to K;
How would you reply to the manager suggestion : The manager's rationale is that with a U-shaped cost curve that is fairly flat at its minimum, the difference intotal annual cost between 800 and 801 units would be small anyway.
How much work is done by gravity on the two block system : A mass m1 = 3.2 kg rests on a frictionless table and connected by a massless string over a massless pulley to another mass m2 = 4.3 kg which hangs freely from the string, How much work is done by gravity on the two block system
Explain neon crystalizes in a face-centered cubic lattice : Neon crystalizes in a face-centered cubic lattice. It's density is 1.45 g/cm3. What is the edge length of the unit cell? Note: The atomic weight of Ne is 20.2 g/mol, and Na is 6.02 x 10^23/mol
Briefly interpret the descriptive data analysis : List and explain the variables you would collect in this study. There must be a minimum of three variables and two must meet the assumptions for a correlational analysis.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the step response equation for charge time

1. What is the step response equation for charge time 2. How to determine the current in RLC circuit using the osciscope 3. List three reseasons why the measured value and pspice value for tau are different.

  What is the speed of the package when it hits the ground

After a package is ejected from the plane, how long will it take for it to reach sea level from the time it is ejected Assume that the package, like the plane, has an initial velocity of 200 mph in the horizontal direction.

  Find the unknown load impedance

The unknown input impedance of a horn antenna operated at a frequency of 300MHz is measured using a slotted transmission line and a Smith Chart. When the antenna is connected to the slotted line, the VSWR on the line is measured to be 4

  A radio receiver for the hf band covers the frequency

A radio receiver for the HF band covers the frequency range 2 MHz to 30 MHz. The first IF frequency is 3.0 MHz and the local oscillator is above the received signal frequency.

  Find the guide wavelength on the line and total attenuation

A copper stripline transmission line is to be designed for a 592 OHMS characteristic impedance. The ground plane separation is 1.02 mm and the dielectric constant is 2.20, with tan = 0.001.

  Compute the mechanical power entering the turbine

A penstock is used to bring water from behind a dam into a turbine. the penstock is 6m in diameter and moves water at a rate of 500 m^3/s. Compute the mechanical power entering the turbine.

  Give signal multiplied by a periodic rectangular pulse train

A aperiodic signal x(t) = 2sinc(2t) is multiplied by a periodic rectangular pulse train s(t) with fundamental frequency F0 = 4 Hz and the fundamental rectangular pulse given by p(t) = 1, -1/80

  Determine what is the power loss per meter

A copper busbar 10cm wide, 5 mm thick, and 10 m long carries a current of 2kA, Calculate the voltage drop if the temperature of the busbar is 120 degree. What is the power loss per meter

  Vhdl coding

The main mission of this project is to design and build a tap changer which is going to be fitted to power transformers for regulation of the output voltage to required levels for the Micro Grid. The tap changer system will consist of 9 changers with..

  Find the parameters of the z-parameter two-port

The following measurement were made on a two-port resistive circuit. With port 1 open, V2 =15V, V1 = 10 V, and I2 = 30 A. With port 1 short-circuited, V2 = 10 V, I2 =4 A, and I1 = -5 A. Find the parameters of the z-parameter two-port.

  What is the value of rth

What is the value of RTH?

  Calculate the rated primary and secondary currents

Calculate: a. The rated primary and secondary currents b. The secondary voltage if it is connected at full load of 2000 kW c. The voltage regulation from no-load to full load. Voltage regulation is given by: (E(no-load)-E (full-load))/E(full-load)..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd