User Account

All Pages

Find the load impedance of lossless coaxial cable

Assignment Help Electrical Engineering
Reference no: EM13272708

Using a 100-Ω slotted lossless coaxial cable, it is found that the distances from the load to the first and second voltage maxima are 1 and 11 cm, respectively, and the standing wave ratio S = 2. Find the load impedance.

Reference no: EM13272708

Questions Cloud

Determine the time-dependent voltage and current at the load : A 200-MHz voltage source with output Vg = 200 V 0 and internal impedance of 100 Ω is connected to the input of the line. Determine the time-dependent voltage and current at the load, and the average power delivered to the load.
What is shortest possible line length to accomplish aim : It is desired to use a short-circuited section of a 60-O lossless line to synthesize an input reactance X = - 120 O. If the operating frequency is 1 GHz and the phase velocity on the line is 0.8
Explain the coordination numbers of li + and s2- : Li2S is pictured n the text on .553. The length of the unit cel i 5.88 x 10^2 pm. For this structure determine:  the coordination numbers of Li + and S2-
The beatles albums : In the course of a 1000-word paper students should summarize the contemporary (i.e., 1960s) critical response to one of The Beatles' albums.
Find the load impedance of lossless coaxial cable : Using a 100-Ω slotted lossless coaxial cable, it is found that the distances from the load to the first and second voltage maxima are 1 and 11 cm, respectively, and the standing wave ratio S = 2. Find the load impedance.
Explain the melting points of nafand nacl : The melting points of NaF, NaCl, NaBr and NaI are 988, 801, 755 and 651 degrees Celsius, respectively. Are these data consistent with ideas developed in Section 12-5
Determine the transmission line parameters of coaxial cable : Determine the transmission line parameters of a coaxial cable that uses aluminum inner and outer conductors with radii a = 2.5 mm and b = 5 mm, respectively, and polystyrene (which is nonmagnetic) as an insulator.
What was the current in the primary : A certain transformer has 500 turns on the primary. If 10 volts are applied to the primary, what was the current in the primary
Determine the complex reflection coefficient at the load : A 50-O lossless line is terminated in a load impedance of 50 + j 100 O. If the wavelength is 20 cm, determine (a) the complex reflection coefficient at the load, (b) the standing-wave ratio,

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Compute the raw data rate provided for each user

The U.S. Digital Cellular provider uses a TDMA scheme for multiple access. It uses a 48.6 kbps data rate and supports three users per frame. Each user occupies two of the six time slots per frame. Compute the raw data rate provided for each user.

  Can buck converter with synchronous rectifier operate in dcm

Can A Buck Converter with Synchronous rectifier operate in DCM at a light load If the load is disconnected how does this affect the Inductor current

  Determine the probability of the chosen number

Generate 1000 random variables that are normally distributed with mean 0 and standard deviation 50. Pick a number at random out of these random variables. Hint: Leverage the capabilities of the for loop to simplify the code.

  What is the magnetic dipole moment of each cobalt atom

determine that the total field B within the sample is one tesla. Calculate M and determine what percentage of the volume now consists of domains with magnetization parallel to the field.

  What is the snr that could be tolerated without error

If the data stream is transmitted using a bandwidth of 64 kHz in an ordinary system (without spread spectrum), what is the SNR that could be tolerated without experiencing significant errors

  Calculate motor speed in revolutions per minute

4.What is the fundamental benefit of PLC controls over manual controls 5.Describe the differences between the two methods of scanning during PLC logic solving. Which method holds the advantage over the other

  Build a home security system circuit

Build a home security system circuit using this program. The system must include a door sensor,window sensor, smoke detector, water leak sensor, a motion detector.

  What is the power level entering the first active stage

What is the power level entering the first active stage of the receiver at 1900 MHz being fed by a 25 meter coax with a loss of 20 dB/km, given that the Isotropic Receive Level is -134 dBW and the receiving station has a 1 meter radius dish

  Describe how would implement it using an open-loop system

Consider a 500-gallon tank that needs to be filled when the level goes below 25 gallons and will stop when the level goes above 475 gallonsControl systems can be either open-loop or closed-loop

  What is base current required and the is for transistor

A pnp power transistor operates with an emitter-to-collector voltage of 5V, an emitter current of 10A, and VEB = 0.85V. For ß = 15, a) What base current is required b) What is the IS for this transistor

  Determine the steady-state frequency deviation

Assuming that there is no frequency-dependent component of the load (i.e., D = 0), find the steady-state frequency deviation and the corresponding new generation of each unit. Use 1000 MVA as the p. u. (per-unit) base.

  Find the junction temperature rise above the room temp

If the breakdown voltage increases with temperature at a rate of 40 mV/"C, find the break-down voltage of the diode at room temperature, assuming that the space-charge resistance is 10 C& independent of temperature.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd