Find the intersection. how do you find the system curve

Reference no: EM13545527

1.What is the formula to find how many gals./ min. would dicharge from a 2 inch dia. hole at 5PSI (with a constant water supply and no friction involved)? Would the same formula apply to any size hole ( ex. 1/2" or 3")?

2.To find the flowrate you have to draw the system curve to find the intersection. How do you find the system curve?

3.A room having a total heat gain of 35,000 btuh is to be maintained at 80 DB and 62 WB. the air is supplied to the room at 60 DB and 55 WB. find the quanity of air to be supplied.

1690 cfm

1500 cfm

1850 sfm

1900 sfm

4.Find the cooling load (in tons of refrigeration) for a room supplied with 10,000 CFM of 95 DB outside air with ratio of 105 gr/lb. The room is to be maintained at 78 DB and humidity ratio of 71.5 gr/lb. The room calculated sensible heat load is 108,000 BTUH and latent load of 30,000 BTUH

34.8 tons

46.3 tons

38.5 tons

73.4 tons

5.The total heat loss from a building equals the heat load or the amount of heat that must be put into the building by the heating system to offset the losses and maintain the proposed comfort zone. The total building heat loss is calculated from losses by which of the following?

A. Conduction

B. Convection

C. Radiation

D. All of the above

Reference no: EM13545527

Questions Cloud

Calculate the axial stress in each bar : The bottom bar is made up of an aluminum bar and a steel bar, each 10 in. long placed in the parallel configuration at 70 F. That is also heated to 300 F.

Plot the shear-force and bending-moment diagrams : Plot the shear-force and bending-moment diagrams for the beam and derive equations for the shear force V and the bending moment M for any location in the beam

Estimate the total cost and cost per linear foot for furnush : Estimate the total cost and cost per linear foot for furnushing and driving steel-sheet piling for construction of the basement of a building, 150 by 240 ft. the piles will be 22 in. wide, 18 ft. long, and weigh 40.3 Ib/Lin ft. the piles will be driv..

What is your speed in mph and ft/s need formulas : You are driving a car your metered fuel flow is 5.97x10^5 csf if at the speed you are driving you are getting 40mpg what is your speed in mph and ft/s need formulas.

Find the intersection. how do you find the system curve : Find the cooling load (in tons of refrigeration) for a room supplied with 10,000 CFM of 95 DB outside air with ratio of 105 gr/lb. The room is to be maintained at 78 DB and humidity ratio of 71.5 gr/lb. The room calculated sensible heat load is 108,0..

Find the single-pipe diameter equivalent to two : Now, knowing ?hp or hl in the 1000’ parallel section, find the single-pipe diameter equivalent to two 12” dia ones. Assume high Rh, so Fig 9.11 applies.

Is this close to the transmission capacity within the system : Say the availability of supply is 60% to, and through Tank “A”, and 40% supplying tank B. Is this close to the transmission capacity within the system to J and C? If not, what do you suggest?

What is the probability that company b would charge more : Two companies, a and b, drill wells in a rural area. Company A charges a flat fee of $3500 to drill a well regardless of its depth. Company B charges $1000 plus $12 per foot to drill a well. the depths of wells drilled in this area have a normal dist..

Project-organisation development plan : Restructure management and realign all the job roles for maximum utilisation of available human resources -Implement one of the training programs in a proposed department

User Account

All Pages