Find the instant centers of all three bars

Assignment Help Mechanical Engineering
Reference no: EM13212866

Two collars C and D move along the vertical rod as shown. Knowing that the velocity of collar C is 50 in/s downward, find the instant centers of all three bars, the angular velocity of AB, the velocity of collard D.

Reference no: EM13212866

Questions Cloud

Explain the anti-periplanar newman projection : Write the anti-periplanar Newman Projection for the first step of the elimination. Using this conformation, be sure to write the correct geometry of the resulting intermediate
Specify a diameter d using a design factor of nd : xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.
Explain the entropy of the systems plus surroundings : If 300kJ of heat are exchanged between the system at -5degrees C and its surroundings at 30degrees C, the entropy of the systems plus
Explain macrs and double declining balance method : A piece of equipment used for research is purchased for $870,000 and is to be depreciated over a specific period of time. If the salvage value at the end of its depreciable life is $50,000, show the yearly depreciation using a) Straight line metho..
Find the instant centers of all three bars : Two collars C and D move along the vertical rod as shown. Knowing that the velocity of collar C is 50 in/s downward, find the instant centers of all three bars, the angular velocity of AB, the velocity of collard D.
Define equilibrium constant for the elctrochemical reaction : The equilibrium constant for the elctrochemical reaction 2Fe+Cu3(PO4)2 = 2FePO4 + 3Cu occuring in aqueous solution
What is the allowable minimum length of the ramp : If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?
What is the percent increase in the air velocity : If the room temperature is 15C and the temperature of the air exiting the hair dryer is 50C, what is the percent increase in the air velocity as it passes through the dryer.
Draw conclusions concerning the process : Draw conclusions concerning the process, and relate your interpretation to the possible existence of chance and assignable causes of variation.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Computing the second moment of area

It is necessary to design a square-section composite bar that will withstand an applied load without deflecting more than a specified amount.The design specification for the bar, including its dimensions and loading criteria, is given below.

  Determine the pressure inside the cylinder

the piston of a piston-cylinder device containing gas has a mass of 60kg and a cross-section area of 0.04m. the local atmospheric pressure is 0.97bar, and the gravitational acceleration is 9.81ms. determine the pressure inside the cylinder?

  Determine the values of q that minimizes unit sales

determine the values of Q that minimizes unit sales cost UC = TC/Q; and compute the annual profit earned by the plant at this quantity.

  Calculate the kg mix- ture from the mixer

calculate the kg mix- ture from the mixer, kg water evaporated, and kg jam produced.

  Determine the acceleration of the block

block c starts from rest and moves downward with a constant acceleration. knowing that after 5 s the velocity of block a relative to block d is 8 ft/s, determine a) the acceleration of the block c. b) the acceleration of portion e of the cable.

  Find the volume of the ring-shaped solid that remains

A cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  Steady state thermal analysis

Steady State Thermal analysis can be use to simulate and obtain results to support the design optimization / objectives

  Find the magnitude of the average velocity

Remember that velocity is a vector quantity so find the magnitude of the average velocity and the angle of average velocity from the horizon

  What is the maximum amount of work

No heat interactions with the environment are allowed. You do not need to describe the details of the process that produces the maximum work, but you do need to describe the final state of the blocks fully.

  What power could be transmitted by a similar shaft rotating

If the maximum shear stress is limited to one-half of its yield strength and the fillet radius is 0.3 in, what is the maximum torque that can be applied? What power could be transmitted by a similar shaft rotating at 400 rpm?

  Estimate the uncertainty in indicated speed

An auto speedometer is graduated in 5 mph increments and has an accuracy rated to be within ±4%. Estimate the uncertainty in indicated speed at 60 mph.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd