Find the height to which the water can be delivered

Assignment Help Mechanical Engineering
Reference no: EM13946600

A centrifugal pump delivers water at the rate of 0.22 m3/s from a reservoir at ground level toanother reservoir at a height H, through a vertical pipe of 0.2m diameter.

Both the reservoirs areopen to atmosphere. The power input to the pump is 90 kW and it operates with an efficiency of75%.

Data: Fanning friction factor for pipe flow is f = 0.004. Neglect other head losses Take gravitational acceleration, g = 9.8 m/s2 and density of water is 1000kg/m3.

The height H, in meters, to which the water can be delivered (up to one decimal place) is____.

Reference no: EM13946600

Questions Cloud

Lead asbestos benzene methylene chloride : OSHA is the only federal agency that publishes exposure limits. The EPA was founded in 1972. EPA limits are legally enforceable. The EPA publishes exposure limits under the Toxic Substances Control Act.
Harris corporation produces a single product : Harris Corporation produces a single product
Temperature and heat flux measurements : What are the molar concentration and the species molar flux of the water vapor at a location (x*, y*) corresponding to the point at which the temperature and heat flux measurements were made in the first case?
Creating new information technology systems for a company : Communication - key; the more they know, the less likely there will be opposition or opposition will be mitigated; email, reports, meetings
Find the height to which the water can be delivered : Find the height to which the water can be delivered - A centrifugal pump delivers water at the rate of 0.22 m3/s from a reservoir at ground level toanother reservoir at a height H, through a vertical pipe of 0.2m diameter.
Determining the approximate water temperature : Water flows at a velocity uoo = 1 m/s over a flat plate of length L = 0.6 m. Consider two cases, one for which the water temperature is approximately 300 K and the other for an approximate water temperature of 350 K. In the laminar and turbulent r..
Metallurgical engineer : A metallurgical engineer decides to set aside money for his newborn daughter's college education.
Famed boston rock and roll club euphoria : On May 1, 1995, the famed Boston rock and roll club Euphoria burned to the ground. Luckily, the fire began at 2:00 a.m. and no one was injured. The highly anticipated and sold out May 2, 1995, concert of the New York rock group Zephyr was cancelle..
Results for the local heat transfer coefficient : Experimental results for the local heat transfer coefficient hx for flow over a flat plate with an extremely rough surface were found to fit the relation

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd