Find the generator load current and new load current

Assignment Help Electrical Engineering
Reference no: EM13226585

A three-phase steam-turbine synchronous generator is connected to an infinite bus. The generator excitation current is IF=1000 A at the time of synchronization with the bus. The generator has a synchronous reactance of Xs =1.5 per unit. With IF unchanged, the steam valves at the turbine are adjusted until the generator delivers an active power of Pg=0.2 per unit. Assuming the infinite bus is the reference voltage (Vt=1 at angle 0),

a)Find the generator load current

b)With the Pg unchanged, the excitation current is increased to 1600 A. Find the new load current.

Reference no: EM13226585

Questions Cloud

Explain information calculate the concentration of i3 : The solubility of I2 (s) in .100 M KI solution at 25 degrees celcius is .05135 moles per liter. The .1 M NaN03 provides the same ionic environment as .1 M KI. From this information calculate the concentration of I3-, I-, I2 in the latter solution ..
Stages and phases that characterize multilateral negotiation : What are the key stages and phases that characterize multilateral negotiations and the WTO promotes free trade through the reduction of transportation costs, language barriers, and exchange rate risk
Explain solution that has a concentration : How many milliliters of a 235 mL solution of 1.5 M AlCl3 must be used to make 61 mL of a solution that has a concentration of 0.5 M Al3+?
What is the quality rating for the composite facility : What is the quality rating for the composite facility? can somebody explain how to get this part? please.
Find the generator load current and new load current : A three-phase steam-turbine synchronous generator is connected to an infinite bus. The generator excitation current is IF=1000 A at the time of synchronization with the bus. The generator has a synchronous reactance of Xs =1.5 per unit.
What are the strengths and weaknesses of each sampling : Research at least three quantitative data collection instruments and sampling methods available to researchers using the text and additional resources from the University Library.
Explain ions will be contained in the dilute solution : A 100 mL stock solution contains 4.1 M Na3PO4. When 31 mL of the stock solution is diluted to 73 mL, how many moles of Na+ ions will be contained in the dilute solution
Explain crystallizes in a face-centered cubic arrangement : Buckminsterfullerene C60 crystallizes in a face-centered cubic arrangement. If potassium atoms fill all the tetrahedral and octahedral holes, what is the formula of the resulting compound?
What is the name of the most common insulating material : 1. Provide 3 ways for creating proto-types of an electronic circuit. 2. Explain briefly, in outline form, and in your own words, the procedure for creating a single-sided, PCB (Printed Circuit Board), using the etching procedure.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Use the magnetization curve

Determine the battery voltage required to obtain a flux density of 1.2 T in the air gap. Use the magnetization curve.

  Explain sketch a block diagram of the arrangement

Sketch a block diagram of the arrangement and calculate suitable values of pad resistance if both the amplifier and the line have a characteristic impedance of 600 Ohm.

  Determine the change in the regulated output voltage

A shunt regulator utilizing a zener diode is biased on through a 100 resistor. Determine the change in the regulated output voltage for the two situations below: a) VI changes +2.0 V, ILoad constant b) ILoad changes +100 mA, VI constan..

  Calculate the natural frequency of oscillation

The bellows, diaphragm, and Bourdon tube pressure sensors all exhibit second order time response. This means that a sudden change in pressure will cause an oscillation in the displacement and, therefore in the sensor output.

  Develop a sensor circuit using commodity components

ETEC 6414 Sensors and Wireless Communications, Assignment 1(a) –Sensor Circuit,  Develop a Sensor Circuit using commodity components

  Explain a certain cache has an access time

A certain cache has an access time of 2 nanoseconds and a hit percentage of 95%. If the main memory access time is 8 nanoseconds, what is the average access time for a read operation?

  How much electricity can a city save in one year

Traffic lights are being converted from incandescent bulbs to LED arrays to save operating and maintenance costs. Typically each incandescent light uses three 100-W bulbs, one for each color R,Y,G,A competing LED array consists of 61 LEDs.

  Calculate the power in each resistor

If R2 = 2R1, R3 = 3R1 and the total power taken by the circuit is 480 watts. Calculate the power in each resistor

  What is the velocity at the end of the pipe

Seawater with a specific weight of 64.0 lbs/ft^3 is at a level of 4 feet above the centerline of the exit pipe. The tank is closed at the top and there is a pressure of 1 psig above the seawater. What is the velocity at the end of the pipe

  Rc circuits: capacitor is completely discharged

Assume that capacitor is completely discharged when t

  What is the value of q we need to inject

If we want to correct the power factor to 0.9 lagging, what is the value of Q we need to inject.

  Locate and specify an appropriate sensor

Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd