Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The following functions are specified as the real part of impedance function Z(s).
Find the function Z(s).
a) R(w) = 16 - 8w2 + w4 /1 +w8
b) R(w) = 2 + 4w2 + 3w4 + w6 / 1 + w8
c) R(w) = -w2 + 2w4 -w8/1 + w8
d) R(w) = 1- 2w2 + w4 / 1- 2w2 + w4 + 4w6
e) R(w) = (1- w2 + w4)2 /(w24 - 4w2 + 3)2 + w2( w4 - 6w2 + 8)2
Suppose you are given an op amp and 20 resistors, each with resistance R. Assuming ideal op-amp behavior, design a circuit which, given input voltages v1, v2, v3, and v4, will deliver a voltage vo, given by vo = 2v1 + 4v2 -2v3-4v4 to a load resist..
A three-phase, 318.75-kVA, 2300-V alternator has an armature resistance of 0.35 /phase and a synchronous reactance of 1.2 /phase. Determine the no-load line-to-line generated voltage and the voltage regulation
Given 4 Bytes of hexadecimal data: 34H, 62H, 43H, and 17H. 1.Find the checksum byte. 2. Perform the checksum operation to ensure data integrity (add the 5 Bytes showing sum equal to zero). 3. If the second byte changes from 62H to 22H, show how the c..
The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4 + j 1.6) ohms per phase between generator G1 and the load, and (0.8 + j1.0) ohms per phase between generator G2 and the load.
load flow problemproblem statement solve the load flow problem below in matlab or similar program using the
A lossy transmission line at 1GHz has the following characteristics: Z0= 50.0 ohms alpha= 0.01 dB/m, Betta=8 rad/m. Determine R, L, G and C for the line
noncausal, linear, and time-invariant. Determine the impulse response for the system and verify that an LTI system defined by the impulse response you determined satisfies the difference equation.
PLC 2 In a motor control system, one master stop pushbutton (Stop) is available for stopping the operation at any time. If the temperature switch (TSW) is closed, pressing the red pushbutton (RedPB) will turn on both motors M1 and M2.
An audio signal s(t) generated by a loudspeaker is reflectedat two different walls with reflection coefficientsr1 and r2. The signal x(t)recorded by a microphone close to the loudspeaker, after sampling,is: x(n) = s(n) + r1s(n-k1) +r2s(n-k2)
Which would you expect to have a bigger effect on the power consumption of a CMOS circuit, a 5% increase in power-supply voltage or a 5% increase in internal and load capacitance
An OpAMP has a unity gain frequency (ft) of 10MHz and a slew rate of 10V/us and AVoc = 120dB at DC (f=0). Assume VCC = -VEE = 15 Volts.a. Approximate the cutoff frequency of the OPAMP itself. b.
Given series circuit and parallel circuit consisting of a 100 ohm resistor and a 10 μF capacitor (100 mH inductor-parallel) and a v(t)= 50sin(1000t+0degree) V source, what is the RMS phasor voltage across the resistor for a series circuit
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd