Find the force ratio equation

Assignment Help Civil Engineering
Reference no: EM13207816

How do you find the force ratio equation to determine the maximum total load that can be applied to a truss?

Given a force of a member how do you find the force ratio?

 

Reference no: EM13207816

Questions Cloud

Methods and procedures for analyzing diversity : Design a model similar to 4-3 in book, with methods and procedures for analyzing diversity and how you would implement the results in a cultural diversity training program
What is the maximum safe speed around the curve : What is the maximum safe speed around the curve? If the speed limit on the roadway is 60mph, what action should be taken by the engineer?
Compute the potential of a platinum electrode : calculate the potential of a platinum electrode immersed in a solution that is prepared by mixing 25 ml of 0.0832 M V2(SO4)3
What happens when the interest rate goes high : Assuming that the current interest rate is 3 percent, compute the value of a three year, 5 percent coupon bond with a face value of $1,000. What happens when the interest rate goes to 4 percent What happens when the interest rate goes to 2 percent
Find the force ratio equation : How do you find the force ratio equation to determine the maximum total load that can be applied to a truss?
What should the strike prices of the put options be : What should the strike prices of the put options be? Assume that the risk-free rate is 10% and the dividend yield on both the portfolio and the index is 2%.
Roman contribution to architecture : Which of the following was a Roman contribution to architecture?
Calculate the ozone column amount in du : Calculate the ozone column amount in DU, corresponding to the pressure profile and ozone concentrations given above. Recall Avogadro's number, NA = 6.0 × 1023 molecules per mole, from which one can calculate [O3]= ..
Explain equilibrium concentrations and equilibrium constant : consider the following reaction, equilibrium concentrations and equilibrium constant at a particular temperature. determine the equilibrium concentration of NO2 (g)

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the design storage and water surface elevation

What is the design storage and water surface elevation at the peak outflow rate and estimate the long-term average reduction (EPA, 1986) in particulates under dynamic conditions.

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  Expected boiling-point elevation

What is the expected boiling-point elevation of water for a solution that contains 271 g of sodium chloride dissolved in 1.0 kg of water?

  Deflection of a simple uniformly loaded beam

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  Estimate the median and 90th percentile load

Estimate the median and 90th percentile load of SS contained in the runoff. Note: COV = coefficient of variance

  Mannering traffic and highway engineering

An approach to a pretimed signal with a 60 sec cycle has nine vehicles in the queue at the beginning of the effective green. Four of the nine vehicles in the queue are left over from the previous cycle.

  Queue problem of vehicles

There are 10 vehicles in a queue when an attendant opens a toll booth. Vehicles arrive at the booth at a rate of 4 per minute. The attendant opens the booth and improves the service rate over time following the function u(t) = 1.1 + .30t, where u(..

  Define the term coefficient of permeability

How would you define the coefficient of permeability? Give typical values of the coefficient for: a) fresh cement pastes; b) hardened cement pastes; c) commonly used aggregates;

  Commencement of fill placement

Determine the horizontal spacing of the vertical drains if the drains are installed in triangular grid to reach 90% of primary consolidation in 1.5 years after the commencement of fill placement.

  Compute the maximum acceptable service load

Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.

  Principal stresses and calculate the max shear stress

At a section in a beam the tensile stress due to bending is 70 N/mm 2 and there is a shear stress of 25 N/mm 2 . Determine from first principles, the magnitude and direction of the principal stresses and calculate the max shear stress.

  Smallest standard commercial pipe

For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of water gage. Determine the smallest standard commercial pipe that will give the required performance.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd