Find the final relative humidity and rate of heat transfer

Assignment Help Mechanical Engineering
Reference no: EM13701031

Outside air at 1 bar, 5 °C and RH 70% is heated to 25 °C. The flow rate of air is 50 m 3/min. Find (a) the final relative humidity, (b) the rate of heat transfer (in kW) needed to heat up the air?

Reference no: EM13701031

Questions Cloud

How policies and legislation could impact the family : Describe three of the major concepts in the family or individual life cycle - Include how self-determination impacts an individual's ability to successfully negotiate challenges in each life cycle.
Using air property tables and specific heat method : Determine the change in entropy for the following: Water, u=1000 kJ/kg, T=140 degree C to saturated liquid at p=3 bar. Air, T(1)= 500 degrees R, p(1)= 10 lbf/in^2 to T(2)= 900 degrees R, p(2)= 50lbf/in^2 (using air property tables and specific heat m..
The rate of entropy production in the heating elements : At steady state, a 750 W electric resistance heater has an outer surface temperature of 450 degrees C on its heating elements. Find the rate of heat transfer from the heater as well as the rate of entropy production in the heating elements
Find relative humidity at outlet and amount of water added : Air at 40 °C, 1 bar, and 10% RH goes through an evaporative cooler, and the outlet air is cooled to 27 °C. Find (a) the relative humidity at the outlet, and (b) the amount of water added (kg H20 per kg of air).
Find the final relative humidity and rate of heat transfer : Outside air at 1 bar, 5 °C and RH 70% is heated to 25 °C. The flow rate of air is 50 m 3/min. Find (a) the final relative humidity, (b) the rate of heat transfer (in kW) needed to heat up the air?
Velocity profile from the navier-stocks equations : I need to be able to derive the velocity profile from the navier-stocks equations. Basically from scratch. Problem 4.36 in the fluid mechanics seventh edition Frank M. White In need to get derived down to the Differential form and find the constant o..
Determine the tension in the cable : A 8 m rectangular gate shown below weighing 200 N is held in place by a horizontal flexible cable as shown in the figure below. Water acts against the gate which is hinged (frictionless hinge) at point A. determine the tension in the cable.
An escape artist is chained and placed : An escape artist is chained and placed in a 1 m x 1 m x 2 m box in which one side is hinged at the top of the box. The box is lowered into water until the top surface is just below the water surface. At that point, an 8 cm diameter hole is opened 0.7..
Where are the respective reference points of particles : Two particles A and B start from rest at the origin s=0 and move along a straight line such that a_A=(6t - 3) ft/s^2 and a_B=(12t^2 - 8) ft/s^2, where t is in seconds. Where are the respective reference points of particles A and B? What are the direc..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd