Find the elapsed time to vaporize the propane and total

Assignment Help Mechanical Engineering
Reference no: EM13629692

A factory has a large liquid propane storage tank. The propane is to be used as vapor. Evaporation of the liquid propane at -42 oC into vapor requires an external heat transfer input of 777,000 kJ. A power cycle steadily generating 55 kW of electricity at thermal efficiency of 20% is installed to supply the required propane heat transfer. Heat transfer absorbed from the surrounding 300 K atmosphere completes the cycle. NOTE: The cycle absorbs heat transfer from the 300 K (hot) environment and heat is transferred into the (cold) propane.

Include a complete schematic diagram in your write-up clearly showing hot (top) & cold (bottom) regions and arrows showing all energy exchanges.

Find the elapsed time to vaporize the propane and total work produced Also find theoretically maximum possible total work output for the given QCOLD, WREV,MAX.

 

Reference no: EM13629692

Questions Cloud

A 200-in diameter rod 15 ft long elongates 012 in under a : a 2.00-in diameter rod 15 ft long elongates 0.12 in under a load of 60 kip. the diameter of the rod decreases 0.0004 in
Water vapor is cooled in a closed rigid tank from 520c and : water vapor is cooled in a closed rigid tank from 520c and 100 bar to a final temperature of 270c. determine the final
What is the work done under the isothermal compression vi : consider a 3-dimensional ideal gas of n particles at temperature ti with an initial volume vi. you adiabatically
384 knowing that the stepped shaft shown tranmits a torque : 3.84 knowing that the stepped shaft shown tranmits a torque of magnitude t2.50 kipin determine the maximum shearing
Find the elapsed time to vaporize the propane and total : a factory has a large liquid propane storage tank. the propane is to be used as vapor. evaporation of the liquid
For the variable length of hospital stay determine the : n the article a multifactorial intervention program reduces the duration of delirium length of hospitalization and
Steam flows steadily through an adiabatic turbine the inlet : steam flows steadily through an adiabatic turbine. the inlet conditions of the steam are 10 mpa 450 ordmc and 80 ms and
Announcing contract award and responsibilities of the : imagine that you are working on a project to purchase 5000 electrical generators with an electrical capacity of three 3
Find the actual cycle coefficient of performance the rate : an electrical window air conditioner with a cooling capacity of of 8000 kjhr draws 6.00 amps of electrical current at

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  What percentage of the bearings will last for 38000000

you have tested bearings for a particular machine. this resulted in a mean of 40570000 cycles with a standard deviation

  A two ton 4000 ibf weight is suspended on a 30 foot long

a two ton 4000 ibf weight is suspended on a 30 foot long half inch diameter steel cable. what was the original length

  Calculate the maximum mass flow rate at the inlet condition

a refrigerant 134a at 140 kpa and -10 degree celcius is compressed by an adiabatic 16kw compressor to an exit state of

  What is the effect of immersion depth

What is the effect of immersion depth on a glass electrode and what aspects of the design of a pH electrode installation would lead to reduced manual maintenance and improved reliability

  Determine temperature at which the water starts boiling

A cooking pot whose inner diameter is 20 cm is filled with water and covered with a 4-kg lid. If the local atmospheric pressure is 101 kPa, determine the temperature at which the water starts boiling when it is heated.

  Determine the radial and transverse components

Neglecting the mass of the rod and the effect of friction, determine the radial and transverse components of the velocity of the collar when r = 0.5 m.

  A 6-lb block is attached to a cable and to a spring

a 6-lb block is attached to a cable and to a spring vertically the cable above and the spring below. the spring

  Dtermine the following a the mass kg and volume m3 of the

a piston - cylinder device initially contains 0.1 m3 of nitrogen gas at 150 kpa and 130 degc. the nitrogen is now

  Calculate the engineering strain and the true strain for

a solid cylindrical specimen 200-mm high is compressed to a final height of 60 mm in two steps between frictionless

  What is a 90 percent confidence interval

What is a 90 percent confidence interval for the standard deviation of the thickness of a washer produced by this procedure?

  The disk in a computer hard drive spins at 7200 rpm at the

the disk in a computer hard drive spins at 7200 rpm. at the radius of 30 mm a stream of data is magnetically written on

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd