Find the conjugate depths of the jump formed in a channel

Assignment Help Civil Engineering
Reference no: EM13313901

The discharge through a 6.0 ft wide rectangular channel is 200.0 ft3/s. Find the conjugate depths of the jump formed in such a channel if 3.5 ft of energy head is lost through it.

Reference no: EM13313901

Questions Cloud

Determine the length of the water column : Mercury is poured into a U-tube. The left arm of the tube has cross-sectional area A1 of 10.4 cm2, Determine the length of the water column in the right arm of the U-tube
Estimate what is the total volume of runoff : It rains 3.0 in. on a 20.0 acre watershed. What is the volume of rainfall excess if 30% of the watershed area is a lake and infiltration on the soil is estimated at 1.0 in. What is the total volume of runoff
Develop a communication plan for the company : Develop a communication plan for the company
What is the minimum bottom width to effect the depth : A trapezoidal channel is to be designed to carry a discharge of 250 cfs at a normal depth of 3.5 ft. The channel is running on a slope of 0.005 ft/ft and the side slopes can be no steeper than 2.5 H on 1 V.
Find the conjugate depths of the jump formed in a channel : The discharge through a 6.0 ft wide rectangular channel is 200.0 ft3/s. Find the conjugate depths of the jump formed in such a channel if 3.5 ft of energy head is lost through it.
Calculate the depth of flow 2 km upstream of the dam : A 12.0 m rectangular channel, having a bed slope of 50 cm/km and a Manning roughness coefficient of 0.015, conveys water at a normal depth of 1.0 m. A dam is built across the channel at which the water depth is 2.0 m.
Calculate the resistance per unit length of the wire : When a potential difference of 2 V is applied across the ends of a wire of 5 m length, a current of 1A is found to flow through it. Calculate: the resistance per unit length of the wire
How much time does it take for the ball to hit the ground : A ball rolls off a platform that is 6.8 meters above the ground. The ball's horizontal velocity as it leaves the platform is 7.4 m/s.How much time does it take for the ball to hit the ground
Evaluate the concentration of hcl : Determine the moles of NaOH b. Determine the moles of HCl c. Calculate the concentration of HCl

Reviews

Write a Review

Civil Engineering Questions & Answers

  How to design a horizontal curve for a two-lane road

design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside lane to provide for stopping sight distanc..

  How much does the student have to pay at the end of 3 years

The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..

  Determine the cycle time for a single engine scraper

Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions.

  Determine how much air is needed combust the water

Soil material is being assessed as a possible liner for a sanitary landfill. A soil core was collected and brought to the laboratory. A 10-cm tall section of soil has 2 cm of water continuously ponded on it. The area of the core surface is 78 cm^2..

  Determine the maximum tensil and compressive stresses

the vertical portion of the press shown below consists of rectangle tube of wall thickness t=8mm. knowing that the press has been tightened on wooden planks being glues together until P = 20 kN,

  What steady-state concentration of co will be observed

If a temperature inversion forms over the city at a height of 0.70 km, how long will it take the carbon monoxide concentration to reach 50 ppm if the wind velocity is zero If the wind velocity is 1 m/s,

  Determine the modulus of elasticity of the material

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 0.50 inch. The gage length is 2 inches. For a load of 13.5 kips, the elongation was 4.66 x 10-3 inches.

  Determine peak discharge if unit hydrograph is triangular

A hydrograph has a uniform rainfall intensity of 1.5 in/hr in the first hour, 2.0 in/hr in the second, and 0.75 in/hr in the third hour. Direct runoff (in inches) using the SCS method is 1.2in.

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m

  Determine additional width l required for all the parameters

The canal shown below is to be widened so that it can carry twice the amount of water. Determine the additional width L required if all other parameters (i.e. flow depth, bottom slope, surface material, side slope) are to remain the same.

  What should be the design capacity of the distribution pipes

A water supply system is being designed to serve a population of 200,000 people with an average per-capita demand of 600L/Person-day (peak demand factor is 1.8) and a needed fire flow of 28,000 L/min.

  Calculate the stress in a rebar subjected to tensile bar

Calculate the stress in a No. 7 rebar subjected to a tensile load of 10,600 lb (in ksi).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd