User Account

All Pages

Find the compression ratio and the mean effective pressure

Assignment Help Mechanical Engineering
Reference no: EM13637346

An Otto cycle has the lowest temperature of 60degreeF and the lowest P as 12psi. The highest temperature is 4040degreeF and the heat addition is 500 Btu/lbm. Find the compression ratio and the mean effective pressure. Use constant specific heat Cv = .171 Btu/lbm degreeR. Is this suitable for modeling a gasoline engine? Comment on any reasons it would or would not be.

Reference no: EM13637346

Questions Cloud

In other words find t2-t1 and how far does the motorcycle : a motorcycle is following a car that is traveling at constant speed on a straight highway. initially the car and the
How would you estimate the effectiveness of the treatment : a trial program is carried out to lower the recidivism rate of convicts that is the rate at which released prisoners
Space shuttle astronauts consume an average of 3000 : 1. space shuttle astronauts consume an average of 3000 calories per day. one meal normally consists of a main dish a
Four identical metallic objects carry the following : four identical metallic objects carry the following charges 2.2 microc 5.4 microc -3.4 microc and -8.8 microc. the
Find the compression ratio and the mean effective pressure : an otto cycle has the lowest temperature of 60degreef and the lowest p as 12psi. the highest temperature is 4040degreef
Given are the standard reduction potentials for the two : given are the standard reduction potentials for the twohalf-reactionscr3aq 3e-nbspregcrs nbspnbspnbspedeg -0.74 vu4aq
The no of coils required for each spring the maximum static : the support for a vibrating sorter consists of a plate sitting on a helical spring with a central plunger through the
Cnsider the point x x24l where x is very large find : a mass m orbits around a planet of mass m in a parabolic orbit of the form y x24l which has focal length l. find the
The planet jupiter has a mass 314 times larger than that of : the planet jupiter has a mass 314 times larger than that of the earth 1.90 x 1027. its radius is 11.3 times larger than

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The corresponding mass flow rates not the original

incoming air flow of 200 m3h at a temperature of 20oc and a humidity ratio of 0.012 kgvkga is mixed in a chamber with

  Determine the ratio db for which a the maximum stress will

a couple m will be applied to a beam of rectangular cross section that is to be sawed from a log of circular cross

  What is the partition coefficient of co for tissue a

two tissues a and b are placed in a gas chamber and equilibrated with carbon monoxide gas at various partial pressures

  Determine the net force acting on block a using newtons 2nd

a downward force of 98 n acts on the free end of the illustrated pulley. ma 47 kg what is block as acceleration?

  A new containment vessel for nuclear waste is being tested

a new containment vessel for nuclear waste is being tested by a group of engineersnbspworking for the u.s. department

  Stagnation pressure ratio across flame holders state 2 to 3

ramjet enginemach number4altitude50000 ftt ambient205 kp11.6 kpah fuel heating value45000 kjkgt peak3000 km mass flow

  In an air compressor the compression takes place at a

in an air compressor the compression takes place at a constant internal energy and 50 kj of heat are rejected to the

  Determine the column height in meters and feet if mercury

mercury is often used in barometers. this is because tje vapor pressure of mercury is low enough to be ignored and

  Steam is flowing in a line at 100 bar it is flashed out

steam is flowing in a line at 100 bar. it is flashed out through a valve to 1 bar pressure. the temperature of the

  Factors affecting the decision for the job offer

Discuss five factors which you are going to consider before making a decision whether to accept or reject the offer and Prepare an organization structure

  The barometer reads 2973 inches hg and the stagnation

a pitot static tube records a static pressure of 5.20 psig and a difference between impact pressure and static pressure

  Calculate the strain-rate sensitivity or m value for al

a strain-rate dependence test is conducted on samples of al 6061-t6. two identical bars are tested. the first bar is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd