Find the change in length in each case

Assignment Help Civil Engineering
Reference no: EM13549278

A 1.0-m rigid horizontal support is hung by two cables as shown. One cable is brass and The other cable is high-density polyethylene plastic. At room temperature (21°C), the cables measure 3.50 m vertically. When the temperature drops to 15°C, find the following:

(a) The change in length in each cable

(b) The change in elevation of points A, B, and C

Reference no: EM13549278

Questions Cloud

What rate of return did the company make on the process : Barron Chemical uses a thermoplastic polymer to enhance the appearance of certain RV panels. The initial cost of one process was $130,000 with annual costs of $49,000 and revenues of $78,000 in year 1, increasing by $1000 per year
What annual rate of return must the endowment fund earn : A permanent endowment at the University of Alabama is to award scholarships to engineering students. The awards are to be made beginning 5 years after the $10 million lump-sum donation is made
Determine the moment of inertia for the shaded area about : etermine the moment of inertia for the shaded area about the y axis. State the method of integration used and label the diagram accordingly.
Determine the magnitude of the reactive force pin o exerts : The pendulum consists of a 10-kg uniform rod and a 15-kg sphere. If the pendulum is subjected to a torque of M= 50 N*m, and has an angular velocity of 3 rad/sec when theta= 45 degrees, determine the magnitude of the reactive force pin O exerts on the..
Find the change in length in each case : A 1.0-m rigid horizontal support is hung by two cables as shown. One cable is brass and The other cable is high-density polyethylene plastic. At room temperature (21°C), the cables measure 3.50 m vertically. When the temperature drops to 15°C
Match each transformation description below with the name : Match each transformation description below with the name of a corresponding transformation. Diffusion-dependent with change(s) in phase composition(s) Diffusionless Diffusion-dependent with non change(s) in phase composition(s) The things you match ..
Dry compressed air enters the heat exchanger at 70 degrees : Gaseous oxygen (99% pure, molar basis) is to be produced at a rate of 350ft^3/hr in a Linde single column plant. The column operates at a pressure of 1 atm. Air leaves the compressor at a pressure of 10 atm.
What is the minimum required heat transfer rate from the : A waste heat source is available at 400°C. A heat engine operates using heat from this source. It rejects heat to the surroundings at 38°C. The power from the engine runs an air conditioner to keep the air inside a building at 25°C
Determine the resulting angular velocity of the wheel : Assume the sample variances to be continuous measurements Find the probability that a random sample of 25 observations, froma normal population with variance ?2=6 will have avariance s^2 a) greater than 9.1 b) between 3.462 and 10.745.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What superelevation rate would you recommend

What superelevation rate would you recommend for a roadway with a design speed of 100 km/hr and a radius of curvature of 500 m? Assume f = 0.11.

  Determine the shear streess and angle of twist at b

A solid titanium is titghly inserted into a hollow section of length l/2 and constan thickness t=7.5mm , and extends from end B towards end A. determine the shear streess and angle of twist at B.

  Determine what is the void ratio of the soil

A natural deposit of soild was found to have water content of 20% and to be 90% saturated. What is the void ratio of the soil

  Determine the effective stress strength parameters

cell pressure kN/m2 100 200 300 ultimate deviator stress kN/m2 137 210 283 ultimate pore pressure kN/m2 28 86 147 determine the effective stress strength parameters

  Determine the resulting angular velocity of the wheel

A bolt located 50 mm fm he center of an automobile wheel is tightened by applying the couple shown for 0.10 s. Assuming that the wheel is free to rotate and is initially at rest, determine the resulting angular velocity of the wheel.

  Calculate the density and specific weight of carbon dioxide

calculate the density and specific weight of carbon dioxide at a pressure of 300 kN/m^2 absolute and 60º C

  Influencing the allowable bearing pressure

What are the two principle factors influencing the allowable bearing pressure in the design of a specific footing- Are both of these factors equally important? Are both factors likely to be equally relevant for different soils types

  Determine the smallest allowable value of p if slipping

A recording tape passes over a 20-mm radius drive drum B and under the idler drum C. Knowing that the coefficents of friction between the tape and the drums are us=.40 and uk=0.30 and that drum C is free to rotate, determine the smallest allowable va..

  Determine the flow rate above the pipe

A 2-inch diameter glass pipe is connected to a pipe network in which the pressure is 70 psig. If the length is 300 feet and the outlet is 10 feet above the pipe, determine the flow rate.

  Sketch scs triangular and curvilinear uhs and mass curve

Sketch the SCS triangular and curvilinear UHs and the mass curve for a 100-mi^2 watershed which is 60% good condition meadow and 40% good cover forest land. The watershed consists of 70% soil group C and 30% soul group A.

  Calculate angle between resultant force and positive x-axis

There are 3 forces acting on the ring. using the non vector approach, determine the resultant force of only the 150 Ib and 100 Ib forces. Also calculate the angle between the resultant force and the positive x axis.

  What is work that must be done on the air in the cylinder

To provide a source of cooling on this hot Florida day, the piston is now pulled up until the air reaches a temperature of -100C. It can be assumed that the process is a polytropic one with.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd