User Account

All Pages

Find the change in diameter under load answer in mm

Assignment Help Civil Engineering
Reference no: EM13528864

A cylinder of rock with a Poisson's ratio of 0.422 has ano-load length equal to 17.6 cm and a no-load diameter of 6.20cm. Under an axial compressive load the axial strain is foundto be -3.44 mm/m.

Find the change in diameter under load. Answer in mm.

Reference no: EM13528864

Questions Cloud

Calculate the magnitude of the electric field in side : A point charge of -2.00μC is locatedin the center of a spherical cavity of radius 6.51cm inside aninsulating spherical charged solid. The charge density in the solid7.34*10^-4 C/m^3.
Find the exact current through the third resistor : A battery supplies 0.77 A to three resistors connected in parallel. What is the exact current (in A) through the third resistor
Find the normal force exerted by the plane on the block : A block weighing 10.82 N rests on a 34° inclined plane. Find the normal force exerted by the plane on the block
Find the centripetal acceleration of the tip of second hand : The speed of the tip of the minute hand on a town clock is 0.00125 m/s. find the centripetal acceleration of the tip of the second hand
Find the change in diameter under load answer in mm : A cylinder of rock with a Poisson's ratio of 0.422 has ano-load length equal to 17.6 cm and a no-load diameter of 6.20cm. Under an axial compressive load the axial strain is foundto be -3.44 mm/m.
Find the value of the normal force : A skier of mass 65 kg skis straight down a 11° slope at constant velocity. Find the value of the normal force
Estimate the tensile strength of the wire and the work : A polycrystalline Al alloy contains a dispersion of hard particlesof diameter 10-8m and average center to center spacingof 6x10-8m measured in the slip planes. Estimatetheir contribution to the tensile yield strength,σy, of the alloy.
Determine what is the charge on the plates : If a capacitance meter applies a charge of 3.0 V across two plates and reads a capacitance of 30 pF, what is the charge on the plates
What force must be applied to push a carton : What force must be applied to push a carton weighing 310 N up a 16° incline, if the coefficient of kinetic friction is 0.41

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine kinetic energy after the stream has slowed down

A section view of a dam shown and water is stored at an elevation of 6 m above the base. the water flows through the dam in a concreate opening 2m high and 3 m wide. there are no losses or friction.

  Design hardwood beam to support a uniformly distributed load

Design a hardwood beam to support a uniformly distributed load of 20 kN over a simply supported span of 8 m. consider bending strength only. Assume that the weight of the beam is 2 kN.

  Determine what is the dry weight of the material

A soil borrow material in its natural state in the ground has a unit weight of 86 pcf. Its natural water content is 9%. What is the dry weight of this material

  Discuss min alignment required to establish the centerline

Include a description of the types of property markers used as well as any problems a surveyor may encounter in this process in your explanation. In addition, discuss the minimum alignment required to establish the centerline

  What does line of collimation means

How to detect eror in line of collimation and what does line of collimation means.

  How many laterals would be required in the leaching field

A time interval of 1.5 hours is recorded for a 6 inch drop of water level in a percolation (perc) test hole. What is the perc rate. How many laterals would be required in the leaching field to serve a 5 bedroom house,

  A three-span continuous h20 timber beam with three equal

a three-span continuous h20 timber beam with three equal spans of 1.3 mts supports a uniform load of 22.46 knm2nbspwith

  Radius of the steel wire ehen stretching with other wire

The aluminium wire has a radius of 1.1mm. What must be the radius of the steel wire if it is to stretch the same distance as the aluminium wire, so that the two wires maintain equal lengths after the masses are attached?

  What is p-value and find critical value of test statistic

The specification for a particular application calls for the blocks to have a mean compressive strength greater than 1350 kPa. A sample of 100 blocks is produced and tested.

  Determine the thickness of the laminar sublayer

For the fully developed flow of water in a smooth 0.15-m pipe at a rate of 0:006m3/s, determine the thickness of a. the laminar sublayer; b. the buffer layer; c. the turbulent core.

  Compute the reynolds number for each of the cases

When working with flow through pipes , engineers typically have to determine if the flow is laminar or turbulent. Compute the Reynolds number for each of the cases below and determine if the flow is laminar or turbulent. Assume all of the conduits..

  Develop an estimate of the volumetric flow rate of air

Develop an estimate of the volumetric flow rate of air that will be required for aeration of the mixed liquor in an activated sludge system.For this calculation, assume that the (ultimate) CBOD is 200 mg/L and (ultimate) NBOD is 50 mg/L.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd