Find the average number of open links

Assignment Help Mechanical Engineering
Reference no: EM13707743

The DNA has N links; each link has a state in which it is closed with energy 0, and a state in which it is open with energy 'e'. The DNA can only unwind from the left; in other words, the sth link can open if all the links to the left (1, 2, 3, ..... s -1) are open. Using a Metropolis Monte Carlo algorithm, find the average number of open links for e = 0.5kT, e = 2kT, N = 20.

Reference no: EM13707743

Questions Cloud

How much charge is on each plate : A 3.2-cm-diameter parallel-plate capacitor has a 2.2mm spacing. The electric field strength inside the capacitor is 1.5 × 105 V/m. How much charge is on each plate
From this information determine where the bird will land : Angry Bird is launched at 20.87 degrees from a height of 18.81 cm at an initial speed of 6.19 m/s. From this information determine where the bird will land
What is the angle between these two displacement vectors : A crow flies 8 km west and 14 km north. A hawk flies 32 km west and 23 km north. What is the angle between these two displacement vectors
Calculate the bullet time of flight : A rifle is aimed horizontally at a target 0.001 m away. The bullet hits the target 0.97 inch below the aim point. What is the bullet's time of flight
Find the average number of open links : The DNA has N links; each link has a state in which it is closed with energy 0, and a state in which it is open with energy 'e'. The DNA can only unwind from the left; in other words, the sth link can open if all the links to the left (1, 2, 3,..
Find the velocity of each snowball the moment they strike : Two children in a tree house 6.5 m above the ground are playing with snowballs. One throws snowball A horizontally at 14 m/s. Find the velocity of each snowball the moment they strike
What is the speed of the shot when he releases it : Sam heaves a shot with weight 16-lb straight upward, giving it a constant upward acceleration from rest of 35.9m/s2 for a height 70.0cm. What is the speed of the shot when he releases it
What is the direction of her net displacement : Anna walks 37 m due north, 90 m due east, and then 57 m due south. What is the direction (angle in degrees) of her net displacement as measured from the x axis
A cylindrical torsion bar is made by bonding a solid bar : A cylindrical torsion bar is made by bonding a solid bar made of material 1 inside a tube made of material 2, as shown below. The yield stresses of the two materials are known as tauy1 and tauy2. Both materials have the same shear modulus, G, a..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd