Find the amplitude of vibration of the motor

Assignment Help Mechanical Engineering
Reference no: EM131146187

An electric motor weighing 750 lb and running at 1800 rpm is supported on four steel helical springs, each having eight active coils with a wire diameter of 0.25 in. and a coil diameter of 3 in. The rotor has a weight of 100 lb with its center of mass located at a distance of 0.01 in. from the axis of rotation. Find the amplitude of vibration of the motor and the force transmitted through the springs to the base.

Reference no: EM131146187

Questions Cloud

Calculate hoop and axial stress in each section : Pressurize assembly to 100 psi. Calculate hoop and axial stress in each section. Design both bolt patterns (number and spacing) for safe operation. Justify your design. Ignore stress concentrations
Find the damping ratio of the isolator : As the speed of the motor is increased from zero, the amplitudes of vibration of the motor are observed to be 0.55 in. at resonance and 0.15 in. beyond resonance. Find the damping ratio of the isolator.
About implementing change development or models : How do/will organizations go about implementing change development or models? And, what is the cross-sections of implementing change, org vision, and org stategy? What does your textbook and the extant research literature purport on this area of inqu..
Think about the threat associated with free trade : Think about the "threat" associated with "free trade." Ross Perot once suggested that NAFTA would create a giant sucking sound, drawing jobs away from the United States. A discussion question might be, "If NAFTA was sucking away important U.S. jobs, ..
Find the amplitude of vibration of the motor : Find the amplitude of vibration of the motor and the force transmitted through the springs to the base.
How would such a condition affect your work life : How is sound transmitted from the environment outside the body to the inner ear? What structures are involved, and how do they transmit sound? What happens in the inner ear (cochlea) when sound waves are converted to neural signals? How is sound ..
Most admired firms-what are their implications : Pfizer, a leading health care firm with $59 billion in revenues, is often rated as one of Fortune’s “Most Admired Firms.” It is also considered an excellent place to work and has generated high return to shareholders. Clearly, Pfizer values its human..
Find the horsepower needed to drive the shaft : A small exhaust fan, rotating at 1500 rpm, is mounted on a 0.2-in. steel shaft. The rotor of the fan weighs 30 lb and has an eccentricity of 0.01 in. from the axis of rotation.
Which of the two is a better financing decision and why : Which of the two is a better financing decision, and why? Show all formulas required to perform these calculations and fully explain your decision making process.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a the largest value less than 45deg of the angle

the initial velocity v0 of a hockey puck is 105 mih. determine a the largest value less than 45deg of the angle a for

  What is the change of energy stored in the battery

A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.

  Determine the initial temperature of the air in the cylinder

Air (assumed to be an ideal gas) is contained in a piston-cylinder assembly at an initial state of 1 bar with a volume of 1 m3. The mass of air contained in the cylinder is 1 kg. During any expansion or compression of the air, the pressure remains co..

  Determine by dimensional analysis

The power P required to drive a fan is believed to depend on density p, flow rate Q, impeller dia. D, and angular veloctiy w in Hz. Determine by dimensional analysis, the general expression for dependence of P on other variables.

  Open globe valve

In Fig there are 125 ft of 2-in pipe, 75 ft of 6-in pipe, and 150 ft of 3-in pipe, all cast iron. There are three 90° elbows and an open globe valve, all flanged. If the exit elevation is zero, what horsepower is extracted by the turbine when the ..

  1 consider the diagram below where a pump is used to draw

1 consider the diagram below where a pump is used to draw water from a lake to feed an irrigation system.a which of the

  Quick return mechanism is to be designed with a time ratio

A quick return mechanism is to be designed with a time ratio=1.22 and a cycle time of 0.2sec. What is the required crank speed (rad/s)? What are theta 1 and theta 2?

  Develop an expression for vmax average velocity flow rate q

a for a rectangular coordinate system we developed the navier stokes equation for vx. now reduce that equation to

  What is the temperature of the propane leaving the valve in

propane vapor enters the valve at 1.5 mpa 70 c and leaves at 0.5 mpa. if the propane undergoes a throttling process

  The 2000 lb load can be moved along the beam bd to any

the 2000 lb load can be moved along the beam bd to any position between stops at e and f. knowing that sigmaall6ksi for

  Determine the slenderness ratio and column constant

A 10 inch long cantilevered beam has a 1” by 1” square cross section. The load at the end of the beam cycles from 0 lbs to 300 lbs. determine the stress. Determine the slenderness ratio and column constant of a 38” long steel column that has a 1.5 in..

  Simply supported beam of length-shear and moment diagrams

Consider a simply supported beam of length 50 ft subjected to a uniformly distributed downward load of 10 kips/ft from x=10 ft to x=40 ft and concentrated downward loads of 100 kips at x=10 ft and x=40 ft. Determine the shear and moment diagrams from..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd