Find the absolute pressure when the barometer reads

Assignment Help Civil Engineering
Reference no: EM13297827

determine the preassure in psi at a depth of 20 ft below the free surface of a body of water and find the absolute pressure when the barometer reads 29.9 inches of mercury.

Reference no: EM13297827

Questions Cloud

Determine time required to reach temperature of panel : A 3-mm thick panel (1 m x 1 m) of aluminum alloy (k = 177 W/m. K, Cp = 875 J/kg. K, and p(rho)= 2770 kg/m3) is heated in a large oven with air at T = 175oC and a convective heat transfer coefficient of h = 40 W/m2.K.
What fraction of original rotational kinetic energy is lost : A wheel is rotating freely at angular speed 920 rev/min on a shaft whose rotational inertia is negligible. What fraction of the original rotational kinetic energy is lost
Describe the concentration of hi is present at equilibrium : At a certain temperature, the equilibrium constant, Kc, for this reaction is 53.3. H2(g)+I2(g) 2HI(g) Kc=53.3 At this temperature, 0.800 mol of H2 and 0.800 mol of I2 were placed in a 1.00-L container to react. What concentration of HI is present ..
General fund and governmental activities general journal : Amber city borrowed $1,000,000 secured by a 5-year mortgage note. This cash from the note was used to purchase a building for vehicle and equipment maintenance. Show how these two transactions should be recorded in the General Fund and governmenta..
Find the absolute pressure when the barometer reads : determine the preassure in psi at a depth of 20 ft below the free surface of a body of water and find the absolute pressure when the barometer reads 29.9 inches of mercury.
Determine the pressure difference between a and b : Fluids A and B ave specific gravities .75 and 1.00 respectively. If the mercury is used as manometer liquid determine the pressure difference between A and B
Find the resonance frequency of the ear canal : Find the resonance frequency of the ear canal, Treat it as a half-open pipe of diameter 8 mm and length 26.7 mm
Coding properly is important to your organization-patient : Explain why it is important for the patients and the health of the organization to correctly use and apply insurance, including verification of benefits. Explain why coding properly is important to your organization and the patient.
Find the increase in vertical stresses due to the weight : The center to center spacing to the two tanks is 14 m. The new tank imparts 150 kPa at the ground surface. Find the increase in vertical stresses due to the weight of the two tanks mid- way between the two tanks at the center of the clay layer.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the mass emissions rate of no2

Assuming that the average stack gas velocity is 10.0m/s and the stack is circular with a 3.0 meter diameter, calculate the mass emissions rate of NO2 in kg/day.

  What is the concentration of ocl-

HOCL is added to water in a tank as a disinfectant. after equilibrium is reached it is found that the pH of the water in the tank is 8.2 and the gas phase partial pressure is the head space of the tank is 0.2E-7 atm. (not: henry's law constant for..

  Determine what is the shear strain at the inner surface

a circular steel tube of length L=1.2m is loaded in torsion. If the inner radius of the tube is 45 mm and the measured angle of twist between the ends is 0.4 degrees, what is the shear strain at the inner surface

  Geometric design and construction of a new two-lane road

Geometric design and construction of a new two-lane two-way road has been recently completed and now it is time for design pavement near Ballarat, Victoria.

  Calculating the force in a punch press

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa.

  Determine what is the balance delay for the solution

A proposal has been submitted to replace a group of assembly workers, each working individually, with an assembly line. The following table gives the individual work elements. The demand rate for this job is 1600 units/week (assume 40h/week)

  Determine the maximum service load

Determine the maximum service load W (kips) at the mid-height of the beam-column shown in the accompanying figure 2.1. Assume the member is hinged with respect to bending in both x and y directions at the top and bottom.

  Calculate the deflection of the beam

Also calculate the deflection of the beam to check that it complies with the design limit of L/200. Only variable actions are required for deflection check.

  What is its specific gravity at 30 percent moisture content

The cross sectional dimensions of a 4-ft-long wood member at 30% moisture content is 1.5 in. x 7.5 in., and its weight is 11 lb. At oven-dry condition, its dimensions and weight are 1.35 in x 6.8 in., and 10.2, respectively. What is its specific g..

  Determine the maximum force

two links AB and DE are connected by a bell crank as shown. Determine the maximum force that can be safely exerted by link AB on the bell crank if the maximum allowable value for the reaction at C is 1600N.

  Determine the horizontal reaction

a gate having cross section shown in fig closes an opening 5 ft and 4 ft high in a water reservoir. The gate weighs 400lb and its center of gravity is 1 ft to the left of AC and 2 ft above BC. Determine the horizontal reaction that is developed on..

  Determine speed of sliding on smooth plane just after impact

If they are sliding on a smooth horizontal plane with the velocities shown, determine their speeds just after impact. The coefficient of restitution between them is e = 0.6. Disks A and B have a mass of 16kg and 11kg , respectively.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd