Find speed and height of saturn v at first stage burnout

Assignment Help Mechanical Engineering
Reference no: EM131383278

Saturn V rocket In first stage of the Saturn V rocket, the initial mass was 2.8×106 kg, of which 2.1×106 kg was fuel. The fuel was burned at a constant rate over 150 s and the exhaust speed was 2, 600 m s-1. Use the results of the last problem to find the speed and height of the Saturn V at first stage burnout.

[Take g to be constant at 9.8ms-2 and neglect air resistance.]

Reference no: EM131383278

Questions Cloud

Find the speed of the centre g of the ball : Initially the ball is at rest at the highest point of the sphere when it is slightly disturbed.- Find the speed of the centre G of the ball in terms of the variable θ, the angle between the line OG and the upward vertical.
What is the effective modulation index : An AM transmitter is modulated by two sine waves, at 1 kHz and 2.5 kHz, with a modulation due to each of 25% and 50% respectively. What is the effective modulation index?
Infrastructure of the production process : Analyze both the structure of the competitive priorities and infrastructure of the production process. Develop three (3) new enablers that are aligned with the long-term plan of Apple. Evaluate three (3) pros and three (3) cons of the new enablers..
General academic writing characteristics : After watching the video write from 2 up to 4 small paragraphs in this Journal expressing in your own voice what's happening in situation shown in the video. Use the general academic writing characteristics: the third person point of view, semifor..
Find speed and height of saturn v at first stage burnout : Saturn V rocket In first stage of the Saturn V rocket, the initial mass was 2.8×106 kg, of which 2.1×106 kg was fuel.- find the speed and height of the Saturn V at first stage burnout.
Addresses some aspect of lockout-tagout : Choose a journal article from the CSU Online Library that addresses some aspect of lockout/tagout. The article itself must be more than one page in length. The EBSCO Database (Business Source Complete) is a good source of journals for safety relat..
Sketch the envelope : An AM signal consists of a 10-MHz carrier modulated by a 5-kHz sine wave. It has a maximum positive envelope voltage of 12 V and a minimum of 4 V.
Find the maximum speed v achieved by the rocket : Gravity is absent. Find the maximum speed V achieved by the rocket. Deduce a two term approximation for V, valid when ? is small.
Show that if drop starts from rest with a negligible radius : A raindrop falls vertically through stationary mist, collecting mass as it falls.- Show that, if the drop starts from rest with a negligible radius, then it has constant acceleration g/7.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd