Find specific yield of aquifer

Assignment Help Civil Engineering
Reference no: EM132416218

Question 1: A volume of 3 x 106 m3 of ground water was pumped out from an unconfined aquifer, uniformly from an area of 5 km2. The pumping lowered the water table from initial level of 102 m to 99 m. Find specific yield of aquifer. Please give the answer of the following question.

Reference no: EM132416218

Questions Cloud

What is the purpose of piles : What is the purpose of piles, and why they could be more preferred compared to shallow foundations.
What is the modulus for the rod : Problem: A rod consisting of a matrix and reinforcing fibers has the following properties: (a) What is the modulus for the rod?
Describe the federal laws or programs in brief : To prepare for this discussion, review the article Tracking Federal Child Care & Early Childhood Education Policy from the Zero to Three website.
Find mean precipitation by the thiessien polygon method : A catchment is in the form of a hexagon of side 8 km. 6 rain gauges installed, one at each corner and one at center recorded
Find specific yield of aquifer : The pumping lowered the water table from initial level of 102 m to 99 m. Find specific yield of aquifer.
How effective is local community in providing opportunities : How effective is your local community in providing lifelong learning c as described in your reading, research, and discussions? What two or three things could.
Prepare an presentation in which you describe each program : Research two educational programs within your community that promote lifelong learning. The programs may be offered through a local library, senior center.
What is the change in storage of aquifer : If the porosity of aquifer is 0.4 and the specific retention is 0.15, what is the change in storage of aquifer.
NEE2201 Linear Systems with MatLab Applications Assignment : NEE2201 Linear Systems with MatLab Applications Assignment Help and Solution, Victoria University, Australia. Laboratory - Second Order Circuit Analysis

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the irreversibility for the condenser

Calculate the irreversibility for the condenser in Problem 7.100 assuming an ambient temperature of 17?C.

  Determine what is the effluent concentration at the rate

A first order reaction occurs in a PFR at the rate of 2.1 hr^-1. The reactor volume is 1400L and flow is 15 gpm. If the influent concentration is 200 mg/L, then what is the effluent concentration

  What is the maximum load that diameter steel cable can hold

What is the maximum load that a .75" diameter steel cable can hold if the UTS of the steel is 145,000 PSI and a safety factor of 1.5 is required?

  Determine whatpressure head is needed from the pump

A WTP Operator is trying to size a pump that takes water from a WTPholding tank and sends it to a house on a hill above theplant. The operator's goal is to have 60 psi of waterpressure entering the house. The operator knows that the head loss (major+..

  Calculate the modal split in percentage for the given value

A calibrated utility function for travel in a city by three modes (car, bus, and light rail) is where X is the cost of travel (cents) and Y is the travel time in minutes. Use logit model to calculate the modal split (in percentage) for the given valu..

  Determine what discharge is available half of the time

By continuous discharge measurements the discharge in stream was determine over a 3-year period. After the data were assembled, it was found that the discharge exceeded 120 cfs 3 percent of the time;

  Which of the material from the above three would you select

A man has a mass of 100 kg. how much pressure would he apply to an I-beam if his shoes each have an area of 50 cm? what is his normal force?

  At what depth of flow does the vehicle begin to move

Assume the vehicle, including the engine compartment is completely sealed. Each tire has about 1 ft by 0.67 ft of tire tread in contact with the road surface. Assume that the specific weight of the water flowing is 62.4 lb/ft3

  Determine the initial weight and final density of the water

A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.

  Determine the normal stress in a soccer ball at pressure

Determine the normal stress in a soccer ball if the internal pressure is 110 kPa, the outside diameter is 220mm and the wall thickness is 3mm .

  Find dimension parameters that affect the drag coefficient

The flow is incompressible, but friction and inertia influences the flow pattern. Use dimensional analysis. Find the dimension parameters that affect the drag coefficient.

  What is the specific discharge in this rectangular channel

A large concrete channel holds a hydraulic jump in which the subcritical depth of flow is 2.5 m.  If 40 percent of the specific energy in the flow is lost through the hydraulic jump, what is the specific discharge in this rectangular channel?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd