Find probability that in sample of bulbs will be defective

Assignment Help Civil Engineering
Reference no: EM13318454

If 3% of the electric bulbs manufactured by a company are defective, Find the probability that in a sample of 100 bulbs, (a) 0 bulbs will be defective (b) 1 bulbs will be defective (c) 2 bulbs will be defective (d) 3 bulbs will be defective (e) 4 bulbs will be defective (f) 5 bulbs will be defective

Reference no: EM13318454

Questions Cloud

How many slices of pizza must you eat : Assuming a typical efficiency for energy use by the body, how many slices of pizza must you eat to walk for 1.5hr at a speed of 5.0 km/hr
The compound with a three-membered ring containing nitrogen : An epoxide is: Student Response Value Correct Answer Feedback A. any compound with a three-membered ring B. basically a cyclopropane C. any compound with a three-membered ring containing oxygen D. any compound with a three-membered ring containing..
What percent increase in shear force would be experience : What percent increase in shear force would be experience on the flat sides of a 40 ft long truck trailer as the truck speed increases from 65 mph to 75 mph. Kinematic viscosity of the air is 1.6x10^4 ft^2/s.
Determine the number of gallons of paint needed to paint : Determine the number of gallons of paint needed to paint the outside surface of the water-supply tank, which consists of a hemispherical bottom, cylindrical sides, and a conical top. Each gallon of paint can cover 250 ft^2
Find probability that in sample of bulbs will be defective : Find the probability that in a sample of 100 bulbs, (a) 0 bulbs will be defective (b) 1 bulbs will be defective (c) 2 bulbs will be defective (d) 3 bulbs will be defective (e) 4 bulbs will be defective (f) 5 bulbs will be defective
What is the minimum grade a student must get in order : The mean grade on a final examination was 72, and the standard deviation was 9. The top 10% of the students are to receive A's. What is the minimum grade a student must get in order to receive an A
Explain the total molar concentration of all the ions : What is the total molar concentration of all the ions in 0.020 M solutions of the following salts in water. 0.020 M KCl = ____ M ions 0.020 M CuSO4 = ____ M ions 0.020 M CaCl2 = ____ M ions
What is the amount of depreciation expense for 2014 : What is the amount of depreciation expense for 2014?
How many students have heights equal to 68 inches : how many students have heights, (a) Greater than 72 inches (b) Less than or equal to 64 inches (c) Between 65 and 71 inches inclusive (d) equal to 68 inches * Assume the measurements to be recorded to the nearest inch.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the speed of the collar when it has moved

Springs AB and CD have a stiffness of k = 300 N/m and k' = 200 N/m, respectively, and both springs have an unstretched length of 600 mm. If the 2-kg smooth collar starts from rest when the springs are unstretched

  Calculate the amplitude of vertical motion of the machine

A machine is supported on four steel springs for which damping can be neglected. The natural frequency of vertical vibration of the machine-spring system is 200 cycles per minute. The machine generates a vertical force p(t)=p0sinwt.

  Determine the dimensions of the best cross section

Water is to be transported at a rate of 60,000 gallons/min in uniform flow in an open channel whose surface are lined with clay tile. The bottom slope is 0.0014. Determine the dimensions of the best cross section

  What is the percentage change in the specific weight

At a depth of 4 miles in the ocean the ppressure is 9520 psia. Assume that the specific weight at the surface is 64.0 lb/ft^3 and that the average volume modulus is 320000psi for the pressure range.

  Determine what will the discharge be in each branch

A 48-in water main carries 79 cfs and branches into two pipes at point A. The branching pipes are 36 and 20 in. in diameter and 2800 and 5000 ft long, respectively. These pipes rejoin at point B and again form a single 48-in.

  How would the economies of construction be obtained

For a metal and wood structure, how would the economies of construction be obtained (pertaining to the mean and standard deviation of a probability of failure graph)?

  What is present worth of five years of cost of maintanance

you purchased an old machine at the beginning of this year.maintanance on this old machine will be 100$ at the end of this year but is expected to increase by $25 each year after. what is the present worth of five years of the cost of maintanance

  Determine the magnitudes of the velocity v and acceleration

A particle which moves in two-dimensional motion has coordinates given in inches by x=t^2-4t+20 and y=3sin2t, where the time t is in seconds. Determine the magnitudes of the velocity v and the acceleration a and the angle between these two vectors..

  Determine the temporary hardness and permanent hardness

A well water has the following mineral contents in mg/L: Na+=20; K+=35; Ca+2 =15; Mg+2 =10; Sr=0.5; Cl- =40; HCO3- =65; CO3-2=5; SO4-2=15; and NO3=10.

  Moles of gas in the gas sample

A gas occupise 250 ml and it's pressure is 550mm Hg @ 254C how many moles of gas are in this sample? (convert mm Hg to atm).

  Determine the required length of super elevation runoff

A simple highway curve is planned to connect two horizontal tangents that intersect at sta. 2500 + 00.00 at an external angle of 52 degrees. For a design speed of 60 mi/hr and a curve radius of about 1.25 times the minimum allowable

  Draw the shear force and bending moment diagram

Consider a beam of length 1.5L(meters) with hinge support and roller support from both the ends (respectively left and right) at distance of L/4. The beam is subjected to triangular loading from 0 to q KNper meter.(left to right)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd