Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
120V, 60 Hz source is connected to a distribution line whose resistance, and inductive reactance is 0.001Ohm, j0.002 Ohm, respectively. Single phase, 100HP, 120V, 0.85 pf. motor and 100Kw, 120V heater are connected in parallel.Find• current flowing in each load before connecting the capacitor and after connecting capacitor,• Line losses before connecting the capacitor and after connecting capacitor,• power factor of the source before connecting the capacitor and after connecting capacitor,• Power consumed by the load before connecting capacitor and after,• Total impedance of the circuit before connecting capacitor and after,• The value of the capacitor to improve the power factor to unity. (connect the capacitor in parallel with the load to improve the power factor)
The 300-kg block is acted upon by a force P, pulling it as shown. P makes an angle of 36o with the horizontal. If the coefficient of sliding friction between the block and the floor is 0.35, determine the force required to start moving the block.
SSB has an advantage over AM with respect to efficiency and power gain. Why, then, is AM commercial broadcast being replaced with SSB transmission
A current amplifier with R=9 kohm Ro=1 kohm and Ais=100 is connected between a 8 V voltage source with a source resistance of Rs=1 Kohm and a load resistance of RL=9 Kohm.
stochastic message signal, m(t), is transmitted down a (noiseless) cable channel by PCM, using an 8-bit code. If the ambient signal is equally likely to lie anywhere between its two extremes, (+/- mp), calculate the ration of the mean squared sign..
3. For a simulated inductor application, to yield L = 75mH, R1 = 3kohm, and C1 = 200uF, determine required value of R2 4. For a constant current generator, with a saturation voltage = 20V and a current reference of 30mA, calculate RLmin.
Discuss the sequential nature of the Ripple Carry Output Adder. Why is it actually a sequential operation What are problems associated with this type of sequential design? How would you alleviate them
computation with 5% of the code that cannot be paralleled, compute the speedup and efficiency.
A sensor with a nominal resistance of 50 ? is used in a bridge with R1 = R2 = 100 ?, V = 10.0 V, and R3 = 100 potentiometer. It is necessary to resolve 0.1 changes of the sensor resistance. A) At what value of R3 will the bridge null
a) What is the minimum sampling frequency b) Specify the number of uniform quantization steps needed and the channel null bandwidth required, assuming that the peak signal-to-noise ratio at the receiver output needs to be at least 30 dB
Writea program to simulate a lottery drawing that uses balls numbered from 1 through 10. Assume that three balls are drawn at random (Userandom numbers or allow user to input the number of lotterydrawings to simulate the random ..
Design an amplifier capable of providing the specified gain over a frequency range of 20 Hz to 10Khz under the following conditions. Input source is 2700ohms resistive, and the output load impedance is 32ohms resistive.
John's house is served electrically by a single phase transformer rated 15 kVA, 8160 / 220 V, 60 Hz. The leakage reactance of the transformer is 400 ohms referred to the high side. John wants to replicate an interesting EEE 360 experiment
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd