Find number of independent dimensionless parameters

Assignment Help Mechanical Engineering
Reference no: EM13701065

Pressurised tank drained through a smooth nozzle, area A m(dot) = m(dot)(del p ,h, row, A, g)

Find:

a) number of independent dimensionless parameters.

b) obtain the parameters

c) state the functional relationship for m(dot)

Please use bucking ham pi-theorem

Reference no: EM13701065

Questions Cloud

Calculate adiabatic flame temperature butane burning : Calculate adiabatic flame temperature butane (C4H10) burning in air at 298 k and 1 atm, assuming complete combustion and constant specific heats.
An ideal refrigeration cycle : An ideal Refrigeration cycle with R134a as the working fluid consists of isentropic compression from saturated vapor at -10 C, constant-pressure heat rejection in the condenser5 at 39 C, constant- enthalpy pressure loss across a throttle valve, and c..
Compute the complex dynamic shear modulus : Binder Classification (Grading) What is the best possible PG grade of the asphalt whose results are shown in Table 4 below? Use Table 9.3 from M&Z at end of assignment to help.
Thermal energy reservoirs : Consider a Carnot heat engine and a refrigerator operating between the same two thermal energy reservoirs. If the thermal efficiency of the heat engine is 0.80, the COP of the refrigerator is?
Find number of independent dimensionless parameters : Pressurised tank drained through a smooth nozzle, area A m(dot) = m(dot)(del p ,h, row, A, g) Find: number of independent dimensionless parameters. obtain the parameters
Compute the force needed to completely submerge the object : Calculate the 2x4 Block's Weight, mass, density and Specific Weight. Express values in both metric and US units. Compute the force needed to completely submerge the object.
Low-speed wind tunnel with atmospheric air : A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behaviour up to Reynolds numbers of Rex = 10^8 , what is the..
Where the hydrodynamic boundary layers meet : Air at 20°C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance where the hydrodynamic boundary layers meet.
What is the equation for the actual air temperature : An electric heater heats air. The temperature sensor has a time constant of 5 seconds. The air temperature output (in °C), as measured by the temperature probe is: T=200+cos(0.5t)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd