User Account

All Pages

Find minimum initial tension require at commissioning stage

Assignment Help Mechanical Engineering
Reference no: EM13906491

You are to design a Flat pulley drive for a refrigeration system with the compressor pulley diameter being 450mm and the motor pulley diameter being 200mm. The two shafts will be 1.95m apart and connected to a closed belt. Find

a. The angle of contact /angle of lap for the two pulleys.

b. Find the required length of belt.

c. Select a suitable belt and, ignoring the elongation at fitting but using the guide mass/unit length, calculate the power transmitted if the maximum permissible tension is 1kN and the coefficient of friction is 0.25 if the motor rotates at 1450rpm.

d. Also find the minimum initial tension require at commissioning stage.

1978_pic.png

Reference no: EM13906491

Questions Cloud

Default and parameterized constructors : Create a class Count with a data member current_count with proper access specifier. Create another tester class (which has main method) to instantiate two counters of Count class.
How many observations are below the median : A sample of single persons receiving social security payments revealed these monthly benefits: $826, $699, $1,087, $880, $839, and $965. How many observations are below the median
Compare string values : Write a program that reads two strings from the keyboard and compares them and prints whether they are equal or not.
The identification of key issues : Grading of answers will be based on the identification of key issues, quality of analysis, and consistency of the problem resolution to the issues and analysis. It evaluates knowledge and comprehension; application and analysis; synthesis and evaluat..
Find minimum initial tension require at commissioning stage : Select a suitable belt and, ignoring the elongation at fitting but using the guide mass/unit length, calculate the power transmitted if the maximum permissible tension is 1kN and the coefficient of friction is 0.25 if the motor rotates at 1450rpm
Fashion pro currently manufacture : Fashion Pro currently manufacture their novelty t-shirts for a contribution margin of 71%. With a sales revenue of $748,992, their fixed costs require 42% of their sales. They have signed with a new company that can produce their shirts, increasing t..
The systematic collection and analysis of publicly : The systematic collection and analysis of publicly available information about consumers, competitors, and developments in the marketing environment
How is kyles gain computed if she sells the stock : Mr. Kyle owns stock in a local publicly traded company. If Kyle is right and the stock price increases in the future, how is his sister's gain computed if she sells the stock?
The tricomponent attribute model : 1)Explain your attitude toward your college/university based on the tricomponent attribute model. Be sure to isolate the cognitive, affective, and conative elements

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Five kg of water is contained in a piston-cylinder assembly

five kg of water is contained in a piston-cylinder assembly initially at 5 bar and 240degc. the water is slowly heated

  Measure the length of the beam what is the torque

measure the length of the beam. what is the torque calibration coefficient? 7 explain any anomalies - differences from

  The automobile shown has 1200kg mass with center of gravity

the automobile shown has 1200kg mass with center of gravity at point g and all wheel have the same 0.34m radius if the

  The temperature of the gases leaving the compressor

A diesel engine is fitted with a turbocharger that comprises a radial flow compressor driven by a radial flow exhaust gas turbine. The gravimetric air-fuel ratio is 20:1; the air is drawn into the compressor at a pressure of 1 bar and at a temperatur..

  Steam enters an adiabatic turbine at 5 mpa and 450degc and

steam enters an adiabatic turbine at 5 mpa and 450degc and leaves at a pressure of 1.4 mpa. determine the work output

  A twisting moment torque t is now applied to the ends of

a thin-walled cylindrical pressure vessel of inner radius 30 mm wall thickness 3 mm and closed ends is subjected to an

  Determine the temperature of the air at the exit in ordmc

at steady state air at 200 kpa 52 ordmc and a mass flow rate of 0.5 kgs enters an insulated duct having differing inlet

  If the power generated by the turbine is 4 mw determine the

steam expands in a turbine steadily at a rate of 25000 kgh entering at 6 mpa and 450? and leaving at 20 kpa as

  Estimate minimum fluidizing velocity for air and for water

For spherical sand particles with Dp = 0.045 inches and the density of each particle is 145 lbm/ft3, estimate the minimum fluidizing velocity for air and for water. Assume a porosity of 32 percent. You may need to rederive Equation 11.41 considering ..

  Determine the force p

the coefficients of static friction and kinetic friction 0.4, 0.30 between all surface of contact. determine the force p for which motion of the 30kg block is impending if cable AB is attached is shown and removed.

  How much per vehicle should the toll be to cover the cost

a city engineer knows that she will need 25 million in 3 years to replace toll booths on a toll road in the city.

  The two purposes of amplification for digital systems

The two purposes of amplification for digital systems are (i) to improve signal-to-noise ratio and (ii) to make good use of the dynamic range of the digitizer; in other words, to ensure the best resolution possible.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd