Find metric tons of gravel required to fill a excavated area

Assignment Help Civil Engineering
Reference no: EM13303404

Calculate the metric tons of gravel required to fill an excavated area 70 meters by 50 meters by 2 meters deep if the gravel has a density of 1890 kg/(m^3).

Reference no: EM13303404

Questions Cloud

What depth of aggregate is needed if angle theta is 40degree : A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees
What is the present value of your windfall : What is the present value of your windfall if the appropriate discount rate is 9 percent?
Provide an analysis of the four attributes of the diamond : For each country, China and India, provide an analysis of the four attributes of the diamond and discuss the relative importance of domestic vs. international factors for the nation's competitiveness of the automotive industry.
What is the difference in the effective annual rates : What is the difference in the effective annual rates charged by the two banks?
Find metric tons of gravel required to fill a excavated area : Calculate the metric tons of gravel required to fill an excavated area 70 meters by 50 meters by 2 meters deep if the gravel has a density of 1890 kg/(m^3).
What amount of bad debt expense was recognized : Accounts receivable less allowance for bad debts of $9,500 and $17,900 for 1999 and 1998 respectively and Kinkos wrote off $10,650 of receivables as bad debts during 1999. What amount of bad debt expense was recognized for the year 1999?
Find the contribution margin per tattoo : Assume that the only service performed is the giving of tattoos, whose unit price is $12. Find the contribution margin per tattoo.
By how many joules does the internal energy change : A 7.4- g piece of silver undergoes isochoric heating, By how many joules does the internal energy change
Determine what is local acceleration along the centerline : velocity of water in the nozzle is given by V=2t/(1-.5x/L)^2. L = 4ft. When x=.5L and t=3s what is the local acceleration along the centerline. What is the convective acceleration.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What would the aquifer specific storage be for the porosity

A confined aquifer has a specific storage of 2.5 * 10^-6 /m . The porosity is .20 and the water compressibility is 5 * 10-10/Pa.For the aquifer skeleton compressibility you just calculated, what would the aquifer specific storage be if porosity were ..

  Discuss the situation where tertiary treatment is required

Biological treatment processes for wastewater can be categorised as dispersed growth and attached growth systems. Discuss the advantages and disadvantages of attached growth systems over dispersed growth systems.

  Pressure on the soil if theta is given

A pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees? Assum..

  Find the load p and stress in the aluminum for the stress

The column is composed of two materials, the inner is brass with a diameter of 100mm and the outer is aluminum with a diameter of 150mm. A rigid flat plate is placed on top to insure that both materials move together when compressed.

  Find the book value of the machine at the end of 2 years

At a local engineering firm, a supervisor thinks about buying a new copy machine for $700 but only wants to keep it for 3 years. Using the DDB find the book value of the machine at the end of 2 years.

  Determine the total dead load-per foot of length

Three-ply asphalt felt and gravel roof over 2in of insulation board is supported by 18in deep precast reinforced concrete beams with 3ft wide flanges. If insulation weights 3lb/ft 2 and the asphalt roofing weights 5.5lb/ft2, determine the total dea..

  Determination of edta titration

Does the presence of Mg2+ significantly interfere with the determination of Ca 2+ by the EDTA titration?

  Determine what will be the max torque of a solid steel shaft

A solid steel shaft of circular cross section and diameter 6 inches in pure torsion under torque. If E=30x10^6 pse and max shear stress is 30 ksi, calculate the torque. If the shaft was hollow, with an innner diameter of 2 inches and outer diameter..

  What is the length of the partial wavelength

What is the length of the partial wavelength for electromagnetic energy with a frequency of 15 MHz and a phase shift of 263 degrees (in meters)?

  Estimate the et losses for the area in inches and centimeter

The discharge of the river at the basin outlet is measured at an avarage of 650 cfs. assuming that the charge in storage for the system is essentially zero, estimate the ET losses for the area in inches and centimeters for the year

  How to plot the shear and moment across the beam

Write the equations required to express the shear and moment along the entire length of beam. Use an origin at point A, and then repeat computations using an origin at point D. Plot the shear and moment across the beam.

  Design of wastewater treatment plant for a community

Consider the design of wastewater treatment plant for a community wiyh average daily and peak hourly wastewater design flows of 2.0 mgd. The raw sewage has an average of 230 mg/l BOD5 and 260 mg/l of suspended solids.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd