User Account

All Pages

Find line current when transformers are operating at no load

Assignment Help Electrical Engineering
Reference no: EM13280910

hree 150 kVA, 480 V/4000, 60 Hz single phase transformers are to be installed on a 4000 V, 3 phase line. The exciting current has a value of 0.02 pu. Calculate the line current when the transformers are operating at no load.

Reference no: EM13280910

Questions Cloud

How large must the annual payments cover : They expect their investment account to earn 9%. How large must the annual payments at t=5,6 and 7 be to cover Jessica's anticipated college costs?
Which electrical meter are self-powered from internal source : which electrical meters are self-powered from an internal source such as a battery, and which meters draw their power frm the circuit to which they are attached
Discuss how word of mouth communication affects promotion : Discuss how word of mouth communication affects promotion. Give an example of a time when you made a decision to purchase something because of a recommendation from a friend or family member.
Determine the fourier series representation of the signal : Determine the Fourier Series representation of the signal x(t)=-1-2cos(27pi(t)-(pi/4))+cos(63pi(t)-(pi/2)).Sketch the two-sided spectrum of the same signal above.
Find line current when transformers are operating at no load : hree 150 kVA, 480 V/4000, 60 Hz single phase transformers are to be installed on a 4000 V, 3 phase line. The exciting current has a value of 0.02 pu. Calculate the line current when the transformers are operating at no load.
Generate an integer result as close as possible to answer : Write and test an assembly language program that solves the following straight-line equation for y. Generate an integer result as close as possible to the actual answer. Assume variable x is always positive and x is an 8 bit number.
Determine the velocity of the satellite : A 199.9 kg satellite is in a circular orbit of 26,273 miles (42,300,000 m) in radius. What is the velocity (speed) of the satellite
How large will the last deposit be : How large will the last deposit be? Round your answer to the nearest cent.
What is conversion constructor : What is conversion constructor? What is conversion operator? What is diff between malloc()/free() and new/delete?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what is the transfer function of the filter

The following MATLAB command has been used to perform offline filtering y=filter([0.8 -0.8],[1 -0.3],x); Where x and y are the input and output vectors, respectively. What is the transfer function of the filter

  Calculate lenght and exit velocity of the final slab

Thickness is to be reduced in three steps in a hot rolling operation. Each step will reduce the slab to 75% of its previous thickness. It is expected that for this metal and reduction, the slab will widen by 3% in each step.

  What is the percentage of distortion level at the frequency

The sampling frequency in a DSP system is fs = 8khz kHz. A hold circuit is used after the DAC device. What is the percentage of distortion level at the frequency f= 3.4 kHz

  Find roll off attenuates frequency components of a lpf

Design a low pass active filter circuit such that its roll off attenuates frequency components at 10 kHz or more by more than 10 dB. Also, it is desired to have the passband gain positive that does not deviate from 20 dB by more then 3 dB.

  Design a simple alu which has three 4-bit inputs x

Design a simple ALU (Arithmetic Logic Unit) which has three 4-bit inputs x = x3x2x1x0, y=y3y2y1y0 and z= z3z2z1z0, two control signals A and B and output S. The ALU should support the operations described in the following table

  Find the p-n junction led current with doping

An Al0.3Ga0.7As p-n junction LED with doping level ND = 1 x 10^18 cm-3 on n-side and NA=1x10^15 cm-3 on p-side has Vf = 0.9 V forward bias across its junction. The LED cross-section is 200 µm x 200 µm.

  Obtain the power factor of a two-branch parallel circuit

Obtain the power factor of a two-branch parallel circuit whre th efirst branch has Z1 = 2 + j4 ohms and the second Z2 = 6 + j0 ohms. To what value must the 6-ohm resistor be changed to result in the overall power factor of 0.90 lagging

  Find the expression for output signal in terms of t and pi

An input signal given by Vin(t)=5cos(500pi*t)+5cos(1000pi*t)+5cos(2000pi*t) is applied to a basic lowpass RC filter. R=318.3 ohms and C=1 microFarad. Find the expression for the output signal in terms of t and pi.

  Determine system bandwidth for subcarrier frequency spacing

An OFDM system employs 260 data subcarriers, 40 pilot subcarriers, and 34 guard subcarriers to transmit data through a wireless channel. QPSK modulation is employed for each subcarrier.

  Display a message that the value was not in the array

First, generate an array of 20 input random integers in the range between 0 to 30 and display. Then, sort the generated 20 random integer numbers in ascending order using "THE SELECTION SORT" method and display your sorted output data flow chart.

  Show design procedure circuit

Design a m-seguence PN generator using 3 shift registers. Show design procedure circuit and PN sequence and find 16 Walsh codes for modulating (encoding) a 4-bit data packet

  What is the power delivered to r at the critical frequency

C=1000 pF R=10 kohms a. Determine A = Vo/Vi at f = fc for the high-pass filter. b. Determine A = Vo/Vi at two octaves above fc. Is the rise in Vo significant from the f = fc level

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd