Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 120V(rms), variable-frequency source is connected in series with a 100Ω resistor and 100μF Capacitor. Find the input power to the circuit from the source at the frequency where the power factor of thr load is 0.75.
For a 64-PSK modulator with an input data rate(fb) equal to 36 Mbps and a carrier frequency of 100 MHz. A. Determine the minimum double-sided Nyquist bandwidth(fN) and the baud. B. Sketch the output spectrum.
A 20-m3 tank contains nitrogen at 23 C and 600 kPa. Some nitrogen is allowed to escape until the pressure drops to 400 kPa and the temperature to 20 C. Determine the amount of nitrogen gas that has escaped in kg. How much in this in Kmoles
Design a second stage (Rin, Rout, and Av) to meet these specifications: a) the two-stage amplifier has an open circuit voltage gain of 120 b) the open circuit voltage gain of the second stage must be in the range 50-100
Design a dc-coupled one-op-amp circuit that will amplify the -100 mV to +50mV input range to have the maximal gain possible without exceeding the typical guarantee linear output range.
A single-phase, 60-Hz power will be transmitted through the transmission line Each subconductor's radius is 10 cm. There are two configurations, the first one is setting subconductors A and B as a bundle, and C and D as another bundle
Two identical CS amplifiers are connected is cascade. First stage is fed with a source Vsig having a resistance Rsig = 100k Ohm. A load resistance Rl = 10k Ohm is connected to the drain of the second stage.
How to design the logic circuit for a room has three doors, with aswitch next to each door, and one over head light. A person shouldbe able to enter or exit from any door and turn the room light onor off by toggling the switch.
Design a current divider that provides a 1:2 current split. Observe the current and power limitations as in the previous item. Another design constraint is that inserting current meters to measure the current division ratio must not upset this rat..
Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 12mA. The zener has an incremental resistance r(z) = 30 ohms and a knee current of 0.5mA. The regulator operates from a 10-V supply and has a 1.2k-ohm load.
A 230kVA, 2300/230V, 60 Hz, step-down transformer has the following parameters. RH =1.2-ohm, XH =3-ohm, RL =12m-ohm, XL =30m-ohm, Rh+c=2k-ohm, , Xm =1.8k-ohm. If the transformer operates at half load with unity power factor
Signal generator‘s internal impedance is purely resistive and has an open-circuit voltage of 3.5 V. When the generator is loaded with 22 ohms of resistance, its terminal voltage drops to 2.8 V. What is the generator's output impedance (pure resist..
GaAs LED emitting surface size is 180 um by 180 um. The doping levels are NA = 9 E+15 cm-3 and ND = 5 E+17 cm-3. The n-layer is 70 um thick, and the p-layer is 8 um thick.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd