Find how much time is available to change the data

Assignment Help Electrical Engineering
Reference no: EM13267466

The frequency of a clocking signal is 10MHZ and it is used to sample serial data stream. If the data must be stable for 15ns before the leading clock edge and for 10ns after the leading clock edge, how much time is available to change the data between clock pulses?

Reference no: EM13267466

Questions Cloud

What rate of return would you have earned : If you sold the bond today, what rate of return would you have earned on your investment?
What is the depth of the water in the box : A hollow cubical box is 0.30 m on an edge. What is the depth of the water in the box just at the instant that water from the lake begins to pour into the box from the lake
What is the fair price for this stock : A stock expects to pay it's first ever dividend of $1 five years from today. From that point onward, dividends are expected to grow by 10% per year forever. What is the fair price for this stock if it has a required return of 14%?
Explain what maximum mass of nitrogen monoxide : If 750 grams of ammonia and 750 grams of oxygen gas were mixed, what maximum mass of nitrogen monoxide could be produced
Find how much time is available to change the data : The frequency of a clocking signal is 10MHZ and it is used to sample serial data stream. If the data must be stable for 15ns before the leading clock edge and for 10ns after the leading clock edge, how much time is available to change the data bet..
How much total cost would be allocated to the assembly : How much total cost would be allocated to the Assembly activity cost pool?
Find the force exerted by the hinge at this angle : A 6 m board of mass 5 kg is hinged at one end, with a 60 kg block nesting on the board 202 cm from the hinge. Find the force exerted by the hinge at this angle
Find the electron and hole concentrations-mobilities : Find the electron and hole concentrations, mobilities, and resistivities of silicon samples at 300K with an impurity concentration of (a) 5X10^15 boron atoms and (b) 2X10^16 boron atoms and a.5X10^16 arsenic atoms.
Calculate the basic and diluted eps for 2013 : Net Income: $1,200,000 & tax rate is 40%. Calculate the basic and diluted EPS for 2013. Are there any dilutions, if any, in this equity structure?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is most common technique used to correct power factor

In a typical commercial electrical distribution system, which is more common: an inductive power factor, or a capacitive power factor. What is the most common technique used to correct this kind of low power factor.

  Find the internal induced voltage and torque angle

Find the input torque to the generator.If armature current and field current are kept constant, find the new value of the terminal voltage if the power factor is changed to 0.7 lagging.

  Design a low-pass filter that attenuates the noise

A measurement signal has a frequency less than 1 kHz, but there is unwanted noise at about 1 MHz. Design a low-pass filter that attenuates the noise to 1%. What is the effect on the measurement signal at its maximum of 1 kHz

  Calculate the power in each resistor

Three resistors R1, R2 and R3 are connected in series and a supply voltage of 240 V. If R2 = 2R1, R3 = 3R1 and the total power taken by the circuit is 480 watts. Calculate the power in each resistor.

  Design a combinational circuit that compares two numbers

Design a combinational circuit that compares two 4-bit numbers to check if they are equal. The circuit output is equal to 1 if the two numbers are equal and 0 otherwise.

  What is the frequency for a periodic signal with a period

What is the frequency for a periodic signal with a period of 2.5 ns 2.5 GHz 250 MHz 4.0 GHZ 400 MHz 2. Which decimal number is equivalent to 25 10 25 31 32 3. Convert the following decimal negative numbers to their 8-bit, 2's complement formulatio..

  Determine the sending end voltage and current

A three-phase transmission line is 80 mile long and serves a load of 250 MW at 220 KV and 0.8 power factor lagging. The A, B, C, D constants for the line in each phase are: Determine the sending end voltage and current

  Calculate the output voltage and the output waveform

With vs = 3sin200tV, R1=20kohms, Cf=5uF, vc(0) = 1.5V. 2. Calculate the output voltage and the output waveform of the circuit.

  What are frequencies for which transfer function can find

The input to the filter is Vin(t)=5+5cos(1000pi*t)+sin(20000pi*t)+4cos(3000pi*t) V and the output is  Vout(t)=5+5cos(1000pi*t+10deg)+5sin(3000pi*t) V.

  Find the stall current-max speed in rotations per minute

Find the stall current, max speed in rotations per minute (RPM), and armature current at a speed of 480.769 radian/s (4591.006 RPM). Discuss the relationship (if any) between the armature current at max speed

  Calculate the three-phase steady-state short-circuit current

A 150 MVA, 24 kV, 123% three-phase synchronous generator operates with an induced voltage that is twice the rated line-to-neutral voltage. Calculate the three-phase steady-state short-circuit current at the generator terminals.

  Find the total voltage drop in 200 twisted pair wire

A proportional controller for a rotating antenna has a gain Kp of 5 in-oz/deg. The antenna was initially pointing due south, but was then commanded to point southeast. Find the initial torque supplied to the antenna.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd