Find how many of the 15 access points must be blocked

Assignment Help Civil Engineering
Reference no: EM13313816

A four- lane undivided multilane highway ( two lanes in each direction) has 11- ft lanes and 5- ft shoulders. At one point along the highway there is a 4% upgrade that is 0.62 mi long. There are 15 access points along this grade. The peak- hour traffic volume has 2500 passenger cars and 200 trucks and buses ( no recreational vehicles), and 720 of these vehicles arrive in the most congested 15- min period. This traffic stream is primarily commuters. The measured free- flow speed is 55 mi/ h. To improve the level of service, the local transportation agency is considering reducing the number of access points by blocking some driveways and rerouting their traffic. How many of the 15 access points must be blocked to achieve LOS C?

Reference no: EM13313816

Questions Cloud

Explain a standard method for the determination of glucose : A standard method for the determination of glucose in serum is reported to have a standard deviation of 0.40 mg/dL. If s = 0.40 is a good approximation of lower case sigma
Determine present worth for benefit and cost with a project : Benefits associated with a project are $10,000 forever starting in year 1. The costs are $20,000 in year 0 and $20,000 in year 3. What is the B/C ratio at i=12% per year. First determine present worth for benefit and cost, respectively.
Study on sparse matrix collapse : Discuss in what ways such a structure is similar to and/or different than a list.
How far due north did it travel : A car goes 13 miles east, then due North ending up 25 deg North of East from its initial position. How far due North did it travel
Find how many of the 15 access points must be blocked : A four- lane undivided multilane highway ( two lanes in each direction) has 11- ft lanes and 5- ft shoulders. At one point along the highway there is a 4% upgrade that is 0.62 mi long. There are 15 access points along this grade.
State corresponding to the following sets of quantum numbers : What is the subshell corresponding to the following sets of quantum numbers. An example of a subshell is 2s. A) n=3,l=2 b) n=3, l=1
Does boeing exhibit economies of kale in producing jets : The president of a small firm has been complaining to the controller about rising labor and material costs. However, the controller notes that the average costs have not increased during the past year. Is it possible?
Use the electronegativity differences between the atoms : Draw the correct molecular geometries of the following covalent compounds. Use the electronegativity differences between the atoms in each bond pair to determine the presence and direction of individual bond dipoles in each molecule.
Find the force exerted by the ground on each wheel : A 1 530-kg automobile has a wheel base (the distance between the axles) of 2.70 m. Find the force exerted by the ground on each wheel

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine an appropriate pipe diameter and slope for reach

Determine an appropriate pipe diameter and slope for this reach, and establish the pipe invert elevations at the upper and lower manholes. Assume that a minimum earth cover of 2 m above the pipe crown is required.

  What is the average length of queue

Vehicles arrive at a toll booth with a mean arrival rate of 2 veh/min (the time between arrivals is exponentially distributed). The toll booth operator processes vehicles (collects tolls) at a uniform deterministic rate of one every 20 seconds. Wh..

  Is the correct difference in elevation between a and b

A level is set up midway between two wood stakes that are about 300 feet apart. The rod reading on Stake A is 9.65 ft and the reading on stake B is 4.23 ft. The level is then set up 6 feet in front of stake B.

  What is the true settling velocity for such a particle

An old occupational hygiene rule of thumb is that a 10 micrometer (micron) silica particle settles at a rare of 1 ft/min (0.5 cm/s). What is the true settling velocity for such a particle? The density of silica is 2600 kg/cubic meter (2.6 g/cubic ..

  Determine what is the thermal stress generated in the rod

The ¼" thick 6061?T6 aluminum bar is subjected to a tensile force of P = 5 kips. b = 4"; c = 1.5"; d = 2.5"; and the fillet radii are 1". a) Determine the maximum stress in the bar. b) What is the lateral strain in the 1.5" wide section

  Calculate horizontal force required to hold hose in place

Diameter of the hose and the nozzle are .25ft and .1ft respectively. If the pressure inside the hose is 60 psig and the flowrate is 1.2 ft^3/s, calculate the horizontal force required to hold the hose in place.

  Thermal conductivities of aluminum and copper

The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..

  What hydrodynamic model would you use for the system

Solar cookers can be used in less developed countries for cooking and also for thermal disinfection of water. To disinfect water, the water must be heated to about 35 Celsius for 5 hours. Of course, it takes time to raise the temperature of the wa..

  Determine the interplanar spacings for the sets of planes

The atomic radius for iron has been measured to be 0.1241 nm. Determine the interplanar spacings for the (111) and (211) sets of planes

  Calculate the vertical stress at a depth of 4m vertically

Three point loads 10,000, 7500 and 9000 kN act in line 5m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the centre (7500kN) load.

  Determine the weight of the water and the pressure forces

A 30-ft-high, 1-ft-diameter pipe is welded to the top of a cubic container 13 ft * 3 ft * 3 ft2. The container and pipe are filled with water at 20°C. Determine the weight of the water and the pressure forces on the bottom and sides of the contain..

  Find the normal sress and deformation in the wire

a 10.0 inch long 10-guage wire of yellow brass (E=105 GPa) is subjected to an axial tensile force of 400 lbs. Find the normal sress and deformation in the wire. A 10-guage wire has a diameter of 2.588 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd