User Account

All Pages

Find gain in decibels of amplifier that has a straight gain

Assignment Help Electrical Engineering
Reference no: EM131148655

Part 1:

Question 1. An aluminum casting sits on a steel surface. Eight pounds of force is necessary to get it to start sliding. The static coefficient of friction (mu) for aluminum on steel is 0.61. What is the weight of the aluminum casting?

Question 2. A motor was measured to rotate (unloaded) at 5000 rpm, with a 6-V input and 1000 rpm, with a 1.2-V input. What is the transfer function (steady state) for the unloaded motor in rpm/V?

Question 3. In a certain system, an electrical heating element was found to increase the temperature of a piece of metal 10o for each amp of current. The metal expands 0.001 in./deg, and pushes on a load sensor that outputs 1 V/0.005 in. of compression. What is the overall transfer function inV/amp.

Question 4. Which of the following is a open-loop system?

Question 5. Find the gain in decibels of an amplifier that has a straight gain of 7000?

Question 6. Find the current in a ground loop that is 200 m long, has a wire resistance of 0.06 ohms/m, and has a difference of 4 V between grounds?

Part 2:

Question 1. Why would you use an optical isolator if you are connecting a microprocessor to a motor?

Question 2. Describe two ways to get the time when using position sensors to extract velocity information?

Question 3. How does a bimetallic temperature sensor work?

Question 4. Give an example of (1) a time-driven control system, (2) an event-driven control system, and (3) a combined time-and event-driven control system?

Reference no: EM131148655

Questions Cloud

What do you think the advantages of method overloading : What side are you on? What do you think the advantages of method overloading are? How would you use method overloading when writing a program? Critique or defend your classmates' positions
Discuss issues by examining the relevant element of contract : Advise Jim if there is an enforceable contract and will Francis be successful? Discuss the issues by examining the relevant elements of contract.
Write a script that inputs three integers : Write a script that inputs three integers from the user and displays the sum, average, product, smallest and largest of the numbers in an alert dialog2
Prepare cost of goods manufactured and the income statement : Prepare the Cost of Goods Manufactured and the Income statement based on the following numbers:-Inventories: Materials. . . .Beginning $65,000; ending $35,000
Find gain in decibels of amplifier that has a straight gain : Find the gain in decibels of an amplifier that has a straight gain of 7000? Find the current in a ground loop that is 200 m long, has a wire resistance of 0.06 ohms/m, and has a difference of 4 V between grounds?
Analysis of the impact of online shopping : Research proposal: Analysis of the impact of online shopping in leading to customer satisfaction and the growth of fashion industry in India: with special reference to Raymond
Design an arduino uno based motor control circuit : Design an Arduino Uno based 24VDC motor control circuit. The motor should start with the presence of a 5V signal, however it will have its own power supply.
Evaluate the level of responsibility of the company : Based on the information you researched, evaluate the level of responsibility of the company in terms of the effectiveness of the response to the security breach.
What are the budgeted sales for july : What are the budgeted sales for July? -  What are the expected cash collections for July? -  What is the accounts receivable balance at the end of July?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Devise a way to address words of memory using fewer n pins

As more and more memory is squeezed onto a single chip, the numberof pins needed to address it also increases. It is often inconvenient to have large numbers of address pins on a chip. Devise a way to address 2^n words of memory using fewer than n..

  Basic neutralizer control system

Write a short report that analyses the P&ID - Basic Neutralizer Control System: The neutralizer process may be used to adjust the pH of a feed stream.

  Determine the ground state energy of an exciton in si

In addition, the distance between the components of the exciton is always such that there are intervening semiconductor atoms. Thus e in the Bohr formulation must also be replaced by Ks e0, where Ksis the semiconductor dielectric constant.

  Explain how a random variable x is normally distributed

A random variable X is normally distributed with mean u = 10 and standard deviation sigma = 1.5. Find the following probabilities: A. P(8 or equal 8.5).

  Determine the magnitude of the scattering parameters

Determine the magnitude of the scattering parameters for this circuit, using a 30 Ω characteristic impedance.

  Find rms value of voltage source and average power delivered

A sinusoidal voltage source given by V(t)=100cos100pi*t V is applied across a 50-ohm resistor. (a) Plot v(t) to scale versus time. (b) Find the instantaneous power and plot it to scale versus time. (c) Find the rms value of the voltage source and the..

  Write it as the real part of a complex exponential

Represent each complex amplitude as a vector in the V -plane, and indicate the location of the frequencies in the complex s-plane.

  Find speed of an electron beam coming from an electron gun

The axis of the cylinder is along the z axis, and the electrons are moving with a velocity vector v in the positive z direction. The velocity of the electrons is 0.1c where c is the speed of light (2.99792458 ´ 108 [m/s]). The magnitude of the cur..

  Connect the the bridge rectifier circuit

Connect the the bridge rectifier circuit shown in Figure 1. Notice that no terminal of the transformer secondary is at ground potential (some simulation software will not run if is not connected to the ground, check yours). The input voltage to the b..

  Compare the equivalent and nominal n circuits for the line

Assuming a positive sequence operation, calculate the exact ABCD parameters of the line. Compare the exact B parameter with that of the nominal n circuit. Also compare the equivalent and nominal n circuits for the line.

  What is the vector part of e1 normal to the interface

If one of the normal vectors to an interface is n-hat = 1/sqrt(13) (3x-hat + 2z-hat) and the electric field just below the interface is E1 = 9x-hat + 2y-hat + 2z-hat, what is the vector part of E1 normal to the interface

  Develop a functional design for a system that measures speed

Develop a functional design for a system that measures and displays the speed of a bicycle. Be sure to clearly identify the design levels, function requirements, and theory of operation for each level.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd