Find expressions for the induced transverse stresses

Assignment Help Mechanical Engineering
Reference no: EM13708089

A cube of linear elastic material is subjected to a vertical compressive stress sigma1 in the 1-direction, but it is now constrained ( e = 0) in both the 2- and 3- directions.

a) Find expressions for the induced transverse stresses, sigma2 and sigma3 in terms of sigma1. Hence derive an expression for the 'effective modulus' (sigma1/sigma2) in this case.

b) Sketch the variation of effective modulus with poison’s ratio and comment on the limiting values when v = 0 (foam) and v=0.5 (rubber).

c) Explain why the rubber soles of running shoes are designed with some combination of air or gel pockets, partially foamed rubber and a tread.

Reference no: EM13708089

Questions Cloud

What is the initial rate of mass loss through the cylinder : Helium gas is stored at 100*C under a pressure of 5x10^5 Pa in a glass cylinder 20 cm in diameter and 15cm long. The glass walls are 5 mm thick. Overtime the Helium will gradually diffuse out of the cylinder. What is the initial rate of mass loss thr..
Determine the magnitude of the principal stresses at point : The maximum shear strain at a point in a thin elastic plate is given as gamma (max) = 450(mu). it is also known that the sum of the normal stresses on two perpendicular planes passing through the point is 30 mpa. Determine the magnitude of the princi..
Refrigerant gains heat it flows through pipe and leave pipe : Refrigerant 134a enters a 28-cm diameter pipe steadily at 200 kPa and 20C with a velocity of 5 m/s. The refrigerant gains heat as it flows through the pipe and leaves the pipe at 180 kPa and 40 C.
Calculate heat transfer : A rigid 15-L vessel initially contains a mixture of liquid water and vapor at 110 C with 11.2 qualities the mixture is then heated until the temperature is 155 C. Calculate heat transfer
Find expressions for the induced transverse stresses : A cube of linear elastic material is subjected to a vertical compressive stress sigma1 in the 1-direction, but it is now constrained ( e = 0) in both the 2- and 3- directions. Find expressions for the induced transverse stresses, sigma2 and sigma3 in..
Estimate the molar volume : The Molar Volume of Al2O3 at 25 Degrees Celsius and 1 atm is 25.715 cc/mol. Its coefficient of thermal expansion is 26 x10^-6 K^-1 and the coefficient of compressibility is 8.0 x10^-7 atm^-1. Estimate the molar volume of Al2O3 at 400 degrees Celsius ..
Calculate the average linear velocity : An aquifer has a hydraulic conductivity of 12 ft/day and an effective porosity of 17% and is under a hydraulic gradient of 0.0055 m/m. Calculate the specific discharge in m/s. Calculate the average linear velocity in m/s.
Determine the volume of the tank : A tank that volume is unknown is divided into two parts by a partition. One side of the tank contains 0.01 m3 of refrigerant R-134a that is a saturated liquid at 0.8 MPa, while the other side is evacuated. The partition is now removed, and the refrig..
Human body-what is the oxygen pumping rate in g per minute : Consider human body. A 70 kg human has about 5 L of blood and it is pumped by heart at about 5.2 LPM (liter of liquid blood per minute). At any given time, the lungs transfer oxygen from alveoli to blood capillaries and the oxygen concentration in bl..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the amount of work input a refrigerator needs to

calculate the amount of work input a refrigerator needs to make ice cubes out of a tray of 0.25 kg of liquid water at

  Determine the power needed to drive the pump if the pump

a feed water pump operates with a flow rate of 350 kgs. the water enters at 420 k. the inlet pressure is 0.7 mpa and

  Sketch the process on a t-s diagram the net work per unit

superheated steam at 18 mpa. 560 degree c enters the steam turbine. the pressure at the exit of the turbine is 0.06 bar

  Consider water as the substance at 30 bar and 450c

consider water as the substance at 30 bar and 450c.a calculate specific volume m3kg using ideal gas equation of state.b

  Given steam flowing thru converging insulated nozzle 25cm

given steam flowing thru converging insulated nozzle 25cm long with inlet diameter of 5cm. at nozzle enterance t325c

  Helium gas enters a nozzle whose isentropic efficiency is

helium gas enters a nozzle whose isentropic efficiency is 88 percent with a low velocity and it exits at 15.3 psia 160f

  Liquid water enters a pump at 15degc 100 kpa and exits at

liquid water enters a pump at 15degc 100 kpa and exits at a pressure of 5 mpa. if the isentropic efficiency of the pump

  The mass flow rate of the refrigerant is 450 kghr a

ammonia enters a heat exchanger operating atsteady state as a superheated vapor at 14 bar 60degc where itis cooled and

  R-134 enters the condenser of a window air conditioning

1. r-134 enters the condenser of a window air conditioning unit at 800 kpa and 35 c and leaves as a saturated

  If the specific internal energy of the gas decreases by

a gas expands in a piston-cylinder assembly from p1 8.2 bar v1 0.0136 m3 to p2 3.4 bar in a process during which the

  The shaft runs in a bearing whose length is 15 times the

a 150mm diameter shaft supporting a load of 10kn has a speed of 1500rpm. the shaft runs in a bearing whose length is

  Calculate valve overlap in crank angle for operational speed

A small five-cylinder CI automobile engine operates with a variable valve timing control system without a camshaft. At operational speed of 3500rpm the intake valve opens 32deg bTDC and closes 57deg aBDC. The exhaust valve opens 52deg bBDC and closes..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd