Find a the conditions and amount of air supplied to the

Assignment Help Mechanical Engineering
Reference no: EM13605446

A building has a total heating load of 200,000 Btu/hr. the sensible heat factor for the space is 0.8 and the space is to be maintained at 72 F db and 30 percent relative humidity. Outdoor air at 40 F db and 20 percent relative humidity in the amount of 1000 cfm is required. Air is supplied to the space at 120 F db. Water vapor with enthalpy of 1150 Btu/lbma is used to humidify the air. Find (a) the conditions and amount of air supplied to the space, (b) the temperature rise of the air through the furnace, (c) the amount of water vapor required, and (d) the capacity of the furnace. Assume sea-level pressure. Could use a basice explanation. My professor does not teach and really just need an explanation of what is going on in the problem and how to set it up.

Reference no: EM13605446

Questions Cloud

What reasons can you think of to explain why takeover co is : goodwill-effect on roi and operating income goodwill arises when one firm acquires the net assets of another firm and
Use the data to estimate the population standard deviation : john calipari head basketball coach for the 2012 national champion university of kentucky wildcats is th ehighest paid
Determine the power needed to drive the low speed turbine : determine the power needed to drive the low speed turbine given maximum velocity in the test section 140 mih with 12 x
A bobsled slides down an ice track starting at zero : a bobsled slides down an ice track starting at zero initial speed from the top of an 44.9 m high hill. the acceleration
Find a the conditions and amount of air supplied to the : a building has a total heating load of 200000 btuhr. the sensible heat factor for the space is 0.8 and the space is to
On january 2 2011 the crossover band acquires sound : on january 2 2011 the crossover band acquires sound equipment for concert performances at a cost of 55900. the band
When you drink liquid through a straw is it more accurate : when you drink liquid through a straw is it more accurate to say the liquid is pushed up the straw rather than sucked
There is a concept that captures the lsquomessage of the : there is a concept that captures the lsquomessage of the material and that concept can be summarized in a one word
At a certain time a particle had a speed of 70 ms in the : at a certain time a particle had a speed of 70 ms in the positive x direction and 1.2 s later its speed was 39 ms in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd