Find a draw a schematic of the power cycle b determine the

Assignment Help Mechanical Engineering
Reference no: EM13638829

Ocean temperature energy conversion (OTEC) power plants generate power by utilizing the naturally occurring decrease with depth of the temperature of the ocean water. Near Florida, the ocean surface temperature is 27oC and at a depth of 700 m the temperature is 7oC.

Find: a) Draw a schematic of the power cycle, b) Determine the maximum thermal efficiency that could be expected for this power cycle, and c) Existing OTEC plants have a thermal efficiency of only 2%, comment on the feasibility of operating an OTEC plant (pros and cons of the system).

Reference no: EM13638829

Questions Cloud

If a balloon is filled with helium until the diameter is : a tank with volume 0.100m3 is filled with helium gas. if a balloon is filled with helium until the diameter is 30.0cm
The percent of observations from the n210 52 distribution : scores on the act test for the 2010 high school graduating class had mean 21.0 and standard deviation 5.2. in all
Determine rate of heat transfer from the wire and if air : a 2-cm long section of a 3-mm in diameter wire is maintained at a constant surface temperature of 370c. the wire is
The reaction n2g 3h2g lt--gt2nh3g is at equilibrium in : the reaction n2g 3h2g lt--gt2nh3g is at equilibrium in areaction chamber. if an experimenter injects a small amount of
Find a draw a schematic of the power cycle b determine the : ocean temperature energy conversion otec power plants generate power by utilizing the naturally occurring decrease with
Explain what happens to pressure on the molecular level : 1. explain what happens to pressure on the molecular level when the number of moles of gas is increased at constant
How much ice in grams would have to melt to lower the : how much ice in grams would have to melt to lower the temperature of 353 ml of water from 26 degrees c to 6 degrees c?
An ammonia molecule nh3 has a permanent electric dipole : an ammonia molecule nh3 has a permanent electric dipole moment 5.0 10-30 cm. a proton is 1.8nm from the molecule in
Your friend gives you a bottle that contains : your friend gives you a bottle that contains eitherhydrochloric sulfuric or phosphoric acid. she also tells you the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the required diameter for a solid circular shaft if

compute the required diameter for a solid circular shaft if it is transmitting a maximum of 110hp at a speed of 560

  What must be its minimum yield strength

A steel alloy to be used for a spring application must have a modulus of resilience of at least 2.07 MPa (300 psi). What must be its minimum yield strength?

  If all transitions between these states and ground occurred

a nucleus has 4 excited states at 0.123 mev 0.216 mev 0.401 and 0.555 mev above the ground state. if all transitions

  Find the compression ratio

Find the compression ratio, cutoff ratio, the thermal efficiency, the mean effective pressure, and the P -v and T-s diagrams clearly showing all corners.

  Find the reversible amount of of work per unit mass find

the air with constant properties in a steady adiabatic flow enters a system at a pressure of 10 bars and 500k with a

  The combustion gases modeled as air enter a turbine at

the combustion gases modeled as air enter a turbine at 6atm 1000k and exits at 1atm 500k. determine the isentropic

  A rigid steel bottle v 025 m3 contains air at 100 kpa 300

a rigid steel bottle v 0.25 m3 contains air at 100 kpa 300 k. the bottle is now charged with air from a line at 260 k

  Refrigerant 134a at a pressure of 08 mpa and a temperature

refrigerant 134a at a pressure of 0.8 mpa and a temperature of 50 c undergoes a process until the pressure is 0.1 mpa

  Calculations for the cooling effect

A reversible heat engine operates between 875 K and 310 K and drives a reversible refrigerator operating between 310 K and 225 K. the engine receives 2000 kJ of heat and the net work output from the arrangement equals 350 kJ. make calculations for..

  If the pressure is 10 psi at the 2in diameter section find

fluid is flowing horizontally at 100gpm from a 2in diameter pipe to a 1in diameter pipe. if the pressure is 10 psi at

  Determine each of the following optimal manufacturing run

1 a toy manufacturing uses 48000 rubber wheels per year for its popular dump truck series. the firm makes its own

  Determine the relevant nozzle areas to expand the gas to

the duct between the turbine and the exit nozzle of a motor is 0.6 m diameter. the gas has a stagnant pressure and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd