Final equilibrium temperature and the total entropy change

Assignment Help Mechanical Engineering
Reference no: EM13719382

A 24.8-kg aluminium block initially at 209ºC is brought into contact with a 17-kg block of iron at 101ºC in an insulated enclosure. Determine the final equilibrium temperature and the total entropy change for this process.

______________ºC (Round to one decimal place)

______________kJ/K (Round to three decimal places)

Reference no: EM13719382

Questions Cloud

How to convert from a displacement vs time graph : How to convert from a displacement vs time graph given, to velocity AND acceleration vs time graphs?
Determine the rate of heat transfer in kw : Carbon dioxide (CO2) gas enters a turbine operating at steady state at 50 bar, 500 K with a velocity of 50 m/s. The inlet area is 0.02 m2. At the exit, the pressure is 20 bar, the temperature is 440 K, and the velocity is 10 m/s.
Calculate the power developed by the turbine : An ideal Rankine cycle uses water as its working fluid. The mass flow rate of water through the cycle is 150 kg/s. saturated vapour enters the turbine at 15 MPa and saturated liquid enters the pump at 10 kPa. Cooling water passes through the condense..
Discuss with the superintendent at her annual evaluation : If Kinsey asked your advice, what kind of three-point plan would you suggest that Kinsey have ready to discuss with the superintendent at her annual evaluation?
Final equilibrium temperature and the total entropy change : A 24.8-kg aluminium block initially at 209ºC is brought into contact with a 17-kg block of iron at 101ºC in an insulated enclosure. Determine the final equilibrium temperature and the total entropy change for this process.
Apply the lumped heat capacity theory : A 10 cm cube of aluminium initially in the oven at a temperature of 300c is immersed in boiling water at a constant temperature if 100c and the convection coefficient of h=900 w/m^2.c
The impact of family violence : A historical perspective on how alcohol and family violence have been impacted by legislative changes - The impact of alcohol abuse on both the addicted individual and those around them
For incompressible flow-derive an analytic expression : The open tank contains water at 20C. For incompressible flow, derive an analytic expression for dl/dt in terms of (Q1, Q2,Q3)
How did the producers decide on the best combinations : 1. Think of a business firm you recently visited (such as Walmart, Home Depot, Red Lobster, Barnes & Noble, McDonald's, etc.). What motivated the producers of all the individual products in the store to make them and offer them for sale? How di..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd