Fill in the following table that specifies

Assignment Help Mechanical Engineering
Reference no: EM131090056

The objective of this exercise is to interface various devices to the computer using DMA synchronization. You may assume the bus bandwidth is at least 8 million bytes/s. For each device you are asked to select the most appropriate DMA mode. Assume the devices support singleaddress DMA. The 16-bit address of the memory buffer used in each case is 0x1234.
Write tape drive Each tape block is 256 bytes. When a tape head is ready, the controller will signal that it is ready to accept all 256 bytes. At this time, the tape interface chip is ready to transfer as fast as possible all 256 bytes from the memory buffer at 0x1234 to the tape.

Sound input The sound waveform buffer is located in memory at 0x1234. Your interface will read the 8-bit ADC 1024 times at 22 kHz and store the data in the buffer. Your software will be smart enough to create two 512-byte buffers out of the 1024 bytes (double buffer) so that it can process one buffer while the A/D data are being stored automatically under DMA control into the other buffer. That is, when the 1024-byte wave buffer has been filled, the DMA system should repeat and fill it up again.
Read hard drive There is a 256-byte buffer at 0x1234 that your DMA system will fill with data from the hard disk. When a hard drive read head is ready, the controller will signal that it has the next byte from the disk. It takes 10 ms for the read head to be ready, then the 256 bytes of data can be transferred from the disk to memory at 2 million bytes/s.

Fill in the following table that specifies the most appropriate mode for each device.

2220_8e6da378-5d73-48c2-bdc4-75334fa160ef.png

Reference no: EM131090056

Questions Cloud

Compute the apr and ear of both loans : 1.) Compute the APR and EAR of both loans 2.) Which loan should you take and why?
Write data required versus write data available : Write data required versus write data available
What is the garbled number : On the evenings financial news broadcast, the reporter states "Last month prices fell by $^#^#& percent. This is an annual rate of deflation of 6.5 percent." What is the garbled number?
Find the width of the river : Find all points of intersections of the 2 circles defined by the equations - Find the width of the river - what is the height of the well?
Fill in the following table that specifies : When a tape head is ready, the controller will signal that it is ready to accept all 256 bytes. At this time, the tape interface chip is ready to transfer as fast as possible all 256 bytes from the memory buffer at 0x1234 to the tape.
Give the answer of following quiz : Question 1. 1. A consensual argument seeks and presents common ground.
Call option price using binomial model : The price is expected to either increase by 8% or decrease by 4% at the maturity of options. If the risk free rate is 4%, calculate the call option price using binomial model.
Compute the after-tax cost of purchasing : It would be depreciated under MACRS using a 5-year recovery period. The firm would pay $5,000 per year for a service contract that covers all maintenance costs. There is no salvage value. Compute the after-tax cost of purchasing
Will you choose them for the print job : Donald Trump says his brand is worth anywhere from $3 to $6 billion. How does he value his brand and has his entering the political arena helped or hurt his brand? Why?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd