Express the total maximum deflection

Assignment Help Civil Engineering
Reference no: EM132416172

Problem: A pin-ended strut of length L subjected to an axial (compression) force P is initially curved and may be assumed to have a symmetric parabolic shape as follows v0=4a(x/L-x^2/L), where a is the initial deflection at the mid-span.

Required:

Question 1: Solve the bending equation and express the total maximum deflection in terms of a and p(=P/Pe).

Question 2: Calculate the maximum deflections for p=0.1 and p=0.9 in terms of a.

Reference no: EM132416172

Questions Cloud

Establish the formula for bulk density of unsaturated : Using a phase diagram and basic definitions of the properties of soil, establish the formula for Bulk Density of unsaturated sample as pw x (Gs+se)/ (1+e).
Determine the surface loading rate in gpd : Determine the surface loading rate in gpd/ft3 (qo), detention time in hours (t), and outlet weir loading rate in mgd/ft (W).
Calculate the mass of water : Question 1: Calculate the mass of water? (in gr) Question 2: How much was the void ratio of the sample prior to compaction?
Mechanisms of evolutionary change : This unit we are learning that there are several mechanisms that lead to evolutionary change within a population or species: mutation, migration, genetic drift,
Express the total maximum deflection : Question 1: Solve the bending equation and express the total maximum deflection in terms of a and p(=P/Pe).
Adhd attention deficit-hyperactivity disorder : There are 3 main different kinds of ADHD, which are the inattentive type, hyperactivity-intensive type, and a combination of both.
Average delay per vehicle resulting from the accident : What is the average delay per vehicle resulting from the accident (assuming D/D/1 queuing)?
Assignment - Thevenin and Norton Equivalent Circuits : The objective of this laboratory is to experimentally determine the Thevenin equivalent circuit of a resistive network driven by a DC voltage source
Determine the thickness of the insulating layer : An insulating material, thermal conductivity 0.08 W / (m. ° C) should be added to reduce heat transfer across the board by 70%.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate maximum magnitude of internal bending moment

Calculate the magnitude and show the location of the maximum compressive and tensile normal stresses on the cross-section and calculate the maximum magnitude of the internal bending moment

  Determine the downward deflection of the tray center

A tray rests on an extendible arm consisting of two steel tubes with two different outer diameters. The downward force at the tray center F0 = 1000 N. Determine the downward deflection of the tray center and the tilt angles of the tray about each ..

  What will be the impact on fish population in the stream

Below a discharge from a wasterwater treament plant , an 8.6km stream has a reoxygenation constant of .4 d^-1, a velocity of .15m/s, a dissolved oxygen concentration of 6mg/L, and an ultimate demand of 25mg/L.

  Write down the speed-density and flow-density equations

Assuming a linear speed-density relationship, the mean free speed is observed to be 60 mph near zero density, and the corresponding jam density is 140 veh/mi.

  Determine if the bridge would fail under a given load

Determine if the bridge would fail under a given load. The truck has two axles and the graph should should begin with 1 axle 7 ft into bridge with the other just reaching the bridge.

  How many passengers per day are carried

A bus line 4 miles long runs through an area with 1/6 acre lots,3.5 people per household, average 1 car per household. People willwalk up to 1/6 mile to a bus stop, so stops are located 1/3 mileapart along the route. Say commuters will tolerate 20 mi..

  Compute the after-tax rate of return using straight line

A $78,000 invtestment in machinery is proposed. It is anticipated that this investment will cause a reduction in net annual operating disbursements fo $16,300 a year for 12 years. The investement will be depreciated for income tax purposes

  Determine the change in exergy of the water flow

For Problem 9.134, determine the change in exergy of the water flow and that of the air flow. Use these values to determine the second-law efficiency of the boiler heat exchanger.

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

  How many tanks do you need

A POTW treats 4 MGD. The SBR is 0.25 MG. How many tanks do you need? Assume that the tank already has 25% of Its volume in sludge and that the fill time is 3 hours, the react time is 2 hours (the total aeration time is 4 hours), the settle time is..

  Determine the maximum value of dz if the flow is to remain

Water flows downhill through a 3 in. diameter steel pipe. The slope of the hill is such that for each mile (5280 ft) of horizontal distance, the change in elevation is Δz.

  Guard helicopter hovers between an island and a damaged

A coast guard helicopter hovers between an island and a damaged sailboat. How would you calculate the direct distance between the helicopter and the sailboat? From the island, the angle of elevation to the helicopter is 73 degrees. From the helicopte..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd