Explore the effects of compressor pressure ratio 2 to 20 in

Assignment Help Mechanical Engineering
Reference no: EM13631165

Explore the effects of compressor pressure ratio (2 to 20 in increments) and mixture ratios (Helium and Xenon) between 0% and 90% by mole fraction of Xenon in increments of 10% to see the effects on net power, thermal efficiency, radiator area, and turbine inlet temperature of the closed Brayton cycle, subject to the following constraints

1. The reactor will apply a steady 300 kW as ?Qin ,

2. Fix the compressor inlet temperature to 300 K. Assume the radiator temperature is the average of T5 and T2.

3. The mass flow rate of the working fluid is 1 kg/s

Produce the following plots to help in describing the results:

1. Net output power (kWe) vs. compressor ratio with curves of constant Xe mole fraction.

2. Thermal efficiency vs. compressor ratio with curves of constant Xe mole fraction.

3. Turbine inlet temperature vs compressor ratio with curves of constant Xe mole fraction.

4. Radiator area vs compressor ratio with curves of constant Xe mole fraction.

The maximum allowable turbine inlet temperature in the real system is 2000K. Discuss the best choice(s) for operating conditions (mixture ratio of Xe and He, and compressor pressure ratio).

Reference no: EM13631165

Questions Cloud

Calculate the number of kilograms of hydrogen that pass per : the purification of hydrogen gas is possible by diffusion through a thin palladium sheet. calculate the number of
If a dielectric material with kappa360 is inserted so that : a parallel-plate air capacitor of area a18.0cm2 and plate separation d2.60mm is charged by a battery to a voltage 68.0
Agolfer hits a ball giving it a maximum height of 20 m : a golfer hits a ball giving it a maximum height of 20 m . if the ball lands 130 m away at the level from which he hit
Oil enters a counterflow heat exchanger at 450k with a mass : oil enters a counterflow heat exchanger at 450k with a mass flow rate of 10 kgs and exits at 350k. a seperate stream of
Explore the effects of compressor pressure ratio 2 to 20 in : explore the effects of compressor pressure ratio 2 to 20 in increments and mixture ratios helium and xenon between 0
Calculate the temperature at which the second state becomes : there are two stable states of caco3 known as aragonite and calcite. using information from the table reference data at
The pliers shown in the figure of the book are used to : the pliers shown in the figure of the book are used to grip a 0.3-in.-diameter rod. knowing that two 60-lb forces are
A 97-mw vertically polarized laser beam passes through a : a 97-mw vertically polarized laser beam passes through a polarizer whose polarizing angle is 15deg from the horizontal.
An rlc oscillator circuit contains a 530nbspomega resistor : 1. an rlc oscillator circuit contains a 53.0nbspomega resistor and a 1.60-mh inductor. what capacitance is necessary

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd