Explanation of riordan supply chain and operational design

Assignment Help Operation Research

Reference no: EM13709656

Explanation of Riordan supply chain and operational design

Problem- Riordan Supply-Chain and Operational Design Analysis Pt.1

Part #1- Quality

Part #2- Previous Assignment Information

Part #3- Riordan Simulation

Part #4- Project Requirements (Dr. Tom)

Part #5- Writing Tense- 3rd Person (He, She, They, or It)

Part #6- Writing Style- Expository (Explain, Review, and Describe - Be Objective - Avoid Personal Opinions)
Minimum Word Count for the Assignment- Between 450 - 600 total words
Answer the following discussion points with operational concepts presented within the course material.
Operational Analysis-

Part #7- Determine Riordan's manufacturing strategy (Chase, Level, or combination) and explain its benefits.

Part #8- Describe how lean production principles may be used to maximize the efficiency and effectiveness of the supply chain process

Part #9- Create an analysis-based process flow diagram for the existing versus the proposed supply-chain and operational processes. Assignment Quality Requirements

Part #10- Includes an active attempt to present the information in a clear, and concise manner

Part #11- Includes one or more supporting citations for each discussion point. The primary supporting citation must be from the course text, and or, course support documents.

Part #12- Includes external support citations from a minimum of two peer-reviewed journal articles less than 5-years old. The supporting article references satisfy the writing requirements for conducting research beyond the course material.
(Basic definitions and concepts not cited from the course text and support materials will result in points deducted from the overall assignment score.)

Part #13- Formatted based on the standard APA citation rules

Part #14- Submitted through the Plagiarism Checker/Grammarly Tools and demonstrate a reasonable attempt to correct quality issues

Part #15- Reviewed and adjusted per writing requirements in the course Instructor

Give me the suitable Define of the analysis of Riordan's supply chain and manufacturing process are analyzed.

Reference no: EM13709656

Questions Cloud

Determine temperature of the air at the outlet of the duct : A 1000 ft long metal duct is used to transport heated air from one side of a plant to another. The duct is 24in high by 36in wide. The heated air's temperature at the inlet of the duct is 170 F and the volumetric flow rate is 15,000 CFM. If the ambie..

Passes through an adiabatic valve in steady flow : Steam at 600 psia and 1000 F passes through an adiabatic valve in steady flow and exits at 14.7 psia. What is the state of the outlet stream? (Give Toutif the outlet is in a single phase region and x out if the outlet is in the two phase region).

Draw the circuit for an rcd snubber circuit : Calculate maximum conduction losses when operating at maximum current and a duty cycle of 5% and design a gate drive circuit.

Determine the quality of the refrigerant at exit of valve : Refrigerant 22 enters the valve of a refrigeration system with a pressure of 14 bars and a temperature of 32 C and exits at a pressure of 4 bars. Neglecting heat transfer and any changes in potential and kinetic energy, determine the quality of the r..

Explanation of riordan supply chain and operational design : Riordan Supply-Chain and Operational Design Analysis and Determine Riordan's manufacturing strategy (Chase, Level, or combination) and explain its benefits.

Wrench is used to loosen a bolt : A 20-centimeter wrench is used to loosen a bolt. The force is applied 0.20m from the bolt. It takes 50 new tons to loosen the bolt when the force is applied perpendicular to the wrench. How much force would it take if the force was applied at a 30-de..

Methane gas in piston-cylinder assembly goes under adiabatic : Methane gas in a piston-cylinder assembly goes under an adiabatic (no heat transfer) quasi- equilibrium compression. (This process is called isentropic process). The pressure and volume of the gas during the process are related as PV 1.3=constant.

Neglect kinetic and potential energy effects : A piston-cylinder assembly contains 2 lbm of water, initially at 100 lbf/in.2 and 400 F. The water undergoes two processes in series: a constant pressure process followed by a constant volume process. At the end of the constant volume process, the te..

Description of academic convenience sampling : Why don't academics consider convenience sampling more often. Give me the brief explanation why convenience sampling is not often used in academics.

User Account

All Pages