Explain what is the ph initially before any titrant is added

Assignment Help Chemistry
Reference no: EM13503089

20.0 mL of a 0.10M weak acid (Ka= 1.56X10^-6) is titrated with a 0.20M strong base.

a. What is the pH initially, before any titrant is added?

b. What is the pH after 5 mL of titrant is added?

Reference no: EM13503089

Questions Cloud

What is the highest price in term of rate per hr : what is the highest price in term of rate per hr that this company should be willing to pay for additional capacity 4 added direct labor time.
How much current flows through the bulb : An automobile has a 24 Watt reading lamp in the ceiling of the car. If it is attached to the 12 Volt car battery, how much current flows through the bulb
Restructuring debt : Restructuring Debt
Find the force on earth due to radiation pressure from sun : At normal incidence, the intensity of sunlight at the Earth is 1400 W/m2. find the force on the Earth due to radiation pressure from the Sun
Explain what is the ph initially before any titrant is added : 20.0 mL of a 0.10M weak acid (Ka= 1.56X10^-6) is titrated with a 0.20M strong base. a. What is the pH initially, before any titrant is added
Calculate the average emf induced in the coil : A rectangular loop is made up of 50 turns of wire and has dimensions of 45 x 55 cm. It is located in a uniform 2 T magnetic field. Over a time of 0.3 s, Calculate the average emf induced in the coil
What overall net income would be produced : What overall net income would be produced if the admission rate of the capitated group were reduced from the commercial level by 10 percent?
Explain what is the ph of a 0.30 m pyridine solution : What is the pH of a 0.30 M pyridine solution that has Kb=1.9x10^-9? the equation for the dissociation of pyridine is C5H5N5(aq)+H2O(l) >>> C5H5NH(aq)+OH-(aq).
What is the coefficient of kinetic friction on rough surface : A block of mass M1=3.5kg moves with velocity v1=6.3m/s on a frictionless suface.It collides with block of mass M2=1.7kg which is initally stationary. What is the coefficient of kinetic friction on the rough surface

Reviews

Write a Review

Chemistry Questions & Answers

  An aerosol spray can with a volume of 441 ml contains 309 g

an aerosol spray can with a volume of 441 ml contains 3.09 g of propane gas as a propellant. what volume would this

  Unknown solution contains only two absorbing species thymol

an unknown solution contains only two absorbing species thymol blue and methylthymol blue. this sample had absorbance

  Calculate the moles of co2

calculate the moles of CO2 you would theoretically expect from 0.203 grams of an alka-seltzer tablet at 700. torr and 285. K.

  A solution of ethanol c2h5oh in water is prepared by

a solution of ethanol c2h5oh in water is prepared by dissolving 76.5 ml of ethanol density 0.79 gcm3 in enough water

  Compute the molar solubility of iron sulfide

Calculate the molar solubility of iron sulfide in a solution that is saturated with hydrosulfuric acid, H2S ( [H2S] = 0.1 M) and has a pH of 2.0. Ka1 = 8.9 x 10^-8 and Ka2 = 1.2 x 10^-13.

  Explain the molecular mass of the blue molecules

If the yellow molecules have a molecular mass of 50 {\rm amu}, what is the molecular mass of the blue molecules

  What is the temperature

A sample of gas occupies 250 mL at STP. What is the temperature if the gas expands to 1500 mL at a pressure of 0.500 atm?

  Explain sucrose is non-disscociated and non-volatile solute

A 10.00 g sample of sucrose (C12H22O11) was dissolved in 200.0 g H2O. What will be the vapor pressure of this solution at 100C? Sucrose is non-disscociated, non-volatile solute.

  Explain what was the purpose of the water

In the reaction between p-aminophenol and aetic anhydride to form acetaminophen, 0.450 mL of water was added. What was the purpose of the water

  State what was the final concentration of her standardized

Sam was standardizing her 4mL iron solution (50 ppm concentration) , but did not exactly add 4.0 mL. Instead he added 4.50mL.

  Explain benzoic acid moles of sodium benzoate are added

0.100 moles of benzoic acid and 0.100 moles of sodium benzoate are added to 1.000 liter of water. What is the final pH

  Calculate the atomic weight of copper

By Solving this problem  student understand about isotopic abundance and how to calculate atomic weight (average atomic mass) of an element -

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd